1. ADDTRON_AF-680_PCMCIA.zip Driver
2. WFW31.TXT File Contents

WFW31.TXT Driver File Contents (ADDTRON_AF-680_PCMCIA.zip)

         Driver Installation Guide for Windows For Workgroups 3.1
      ==============================================================

Introduction
============
    This document describes the procedure to install NDIS 2.0 driver on
    MS Windows for Workgroups 3.1 OS for AF-680 10/100Mbps Fast Ethernet
    PC Card.

    These drivers conform to the Network Driver Interface Specification
    (NDIS 2.01) defined by Microsoft/3Com.

    Location of Driver:   \NDIS2\DOS\AF680.DOS
    Location of Enabler:  \EN680.EXE


Installation Procedure
======================

 A. Installing driver when WFW 3.1 doesn't exist:
    ---------------------------------------------
    1. Run Windows SETUP.EXE. Wait for Windows to request information about
       your network Card. Then select "Unlisted or Updated Network Adapter".
       and press OK button.

    2. Insert the driver disk.

    3. Windows will display a dialog screen to ask the driver path. Then
       enter "A:\NDIS2\DOS" or "B:\NDIS2\DOS" and press return or OK button.

    4. After Windows has read the needed files. It will show another dialog
       screen. You can select hardware configuration as your Card settings.

    4. Continue the installation per Windows for Workgroups instructions.

    5. Before restart your system, add Enabler(EN680.EXE) on CONFIG.SYS. And
       check out if you using any memory management (EMM386, QEMM etc.), you
       must exclude a block memory space for PCMCIA card as sample file.

    6. Now, you can restart your computer to start driver.


 B. Install driver when WFW 3.1 already exists:
    -------------------------------------------

    1. Start your Windows For Workgroups and open main group.

    2. Select "CONTROL PANEL" icon in main group.

    3. Select "NETWORK" icon in control panel window.

    4. Select "ADAPTERS" icon in network window.

    5. Select the Add option.

    6. Select "Unlisted or Updated Network Adapter" and press OK button.

    7. Insert the driver disk.

    8. When a dialog screen is displayed on the screen to ask the driver
       path. Enter "A:\NDIS2\DOS" or "B:\NDIS2\DOS" and press return or OK
       button.

    9. After Windows has read the needed files. It will show another dialog
       screen. You can select hardware configuration as your Card settings.

   10. Before restart your system, add Enabler(EN680.EXE) on CONFIG.SYS. And
       check out if you using any memory management (EMM386, QEMM etc.),
       must exclude a block memory space for PCMCIA card as sample file.

   11. Select reboot computer to restart Windows.


 C. TO ADD NETWARE:
    ---------------

    1. Select the "Control Panel" icon in the Main Group.

    2. Select the "Network" icon.

    3. Select the "Networks" button.

    4. Select "Novell Netware" and select the add button.

    5. Select "OK" and close the Network icon.

    6. Select reboot computer to restart Windows.


    --- Sample CONFIG.SYS file ---

       :
    DEVICE=C:\WFW31\HIMEM.SYS
    DEVICE=C:\WFW31\EMM386.EXE NOEMS X=D000-D3FF
    REM you must load enabler program into system
    DEVICE=C:\WFW31\EN680.exe /irq:5 /iop:320
    DEVICE=C:\WFW31\PROTMAN.DOS /I:C:\WFW31
    DEVICE=C:\WFW31\IFSHLP.SYS
    DEVICE=C:\WFW31\AF680.DOS
       :


    --- Sample PROTOCOL.INI file ---

    [network.setup]
    version=0x3100
    netcard=ms$AF680,1,MS$AF680
    transport=ms$netbeui,MS$NETBEUI
    lana0=ms$AF680,1,ms$netbeui

    [protman]
    DriverName=PROTMAN$
    PRIORITY=MS$NETBEUI

    [MS$NETBEUI]
    DriverName=netbeui$
    SESSIONS=10
    NCBS=32
    BINDINGS=MS$AF680
    LANABASE=1

    [MS$AF680]
    DriverName=AF680$