;*****************************************************************************
;
; This INF file is used to install LAN adapter driver for Windows NT.
;
; Supported OS: Windows NT 3.51 / NT 4.0
; Supported Adapters:
;
; D-Link DL2000-based Gigabit Ethernet Adapter.
; D-Link DGE-550T Gigabit Ethernet Adapter.
;
; Copyright (C) 2001 D-Link Corporation. All rights reserved.
;
;*****************************************************************************
; Revision #: 1.1.10803$
;*****************************************************************************
;*****************************************************************************
; Customization constants
;*****************************************************************************
[ModelConstants]
IHVName = "D-Link"
ModelDescription = "DGE-550T Gigabit Ethernet Adapter"
Ndis3Drvr = "DL2XND3.SYS"
Ndis4Drvr = "DL2XND4.SYS"
CfgFileName = "DL2XCFG.DLL"
DrvrMajVer = "1"
DrvrMinVer = "0"
ModelCode = "DL2X"
VendorID = 4486 ;; 0x1186 (D-Link)
AsicCFID = 1073746310 ;; 0x40001186 = 1073746310
DeviceID = 16384 ;; 0x4000 = 16384
Ndis3FilePath = ""
Ndis4FilePath = ""
CfgSourcePath = ""
;*****************************************************************************
; Default parameters
;*****************************************************************************
TxBuffer = 20 ;; Tx buffers
RxBuffer = 64 ;; Rx buffers
NoCableIndication = 0 ;; Disable
TxStartThreshold = 256 ;; !Store and forward
EnableTagging = 0 ;; Disable VLAN tagging
VLANID = 6 ;; Default VLAN ID
EnableGVRP = 1 ;; Enable GVRP if tagging enabled.
FlowControl = 1 ;; Enable
; FlowOnThresh = 1791 ;; 0x6ff
; FlowOffThresh = 0 ;; 0
IFSSelect = 3 ;; 4352 bit times
ConnectionType = 0 ;; Autosense
JumboFrame = 0 ;; Jumbo Frame Disabled
[Source Media Descriptions]
1 = "D-Link Gigabit Ethernet Adapter Driver CD/Diskette"
[Options]
DL2X
[OptionsTextENG]
DL2X = "D-Link DGE-550T Gigabit Ethernet Adapter"
;*****************************************************************************
; Constants
;*****************************************************************************
[FileConstants]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = $(IHVName)
;*************************************************************************
; Driver version information
;*************************************************************************
ProductMajorVersion = $(DrvrMajVer)
ProductMinorVersion = $(DrvrMinVer)
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = $(ModelCode)
ProductSoftwareTitle = $(ModelCode)" Adapter Driver"
NetRuleSoftwareType = $(ModelCode)"Sys ndisDriver "$(ModelCode)"Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """"$(ModelCode)"Sys"" yes no container"
NetRuleSoftwareClass = {$(ModelCode)"Driver basic"}
NetRuleSoftwareSWBindable = {$(ModelCode)"Driver "$(ModelCode)"Adapter non exclusive 100"}
ProductHardwareName = $(ModelCode)
ProductHardwareTitle = $(IHVName)" "$(ModelDescription)
NetRuleHardwareType = $(ModelCode)" "$(ModelCode)"Adapter"
NetRuleHardwareClass = {$(ModelCode)"Adapter basic"}
AdapterType = 5 ;; PCI board
NetRuleHardwareBindForm = " yes yes container"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
NT351VersionConstant = "3.51"
NT40VersionConstant = "4.0"
;*****************************************************************************
; Language dependent constants
;*****************************************************************************
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
ProductSoftwareDescription = $(IHVName)" "$(ModelDescription)" Driver"
FunctionTitle = $(IHVName)" "$(ModelDescription)" Setup"
ProductHardwareDescription = $(IHVName)" "$(ModelDescription)
NoList = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(FunctionTitle)
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Network card is not present in the system"
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
;*****************************************************************************
; Files
;*****************************************************************************
[Files-Inf]
2, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename)
[Ndis3File-DL2X]
1, $(Ndis3Drvr), SIZE=999
[Ndis4File-DL2X]
1, $(Ndis4Drvr), SIZE=999
[CfgFile-DL2X]
1, $(CfgFileName), SIZE=999
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
;*****************************************************************************
; [Identify]
; Returns information to Setup about the type of driver or drivers that
; can be installed by this INF file.
;*****************************************************************************
[Identification]
OptionType = NetAdapter
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;*****************************************************************************
; [ReturnOptions]
; This section returns information to the Setup program, listing the names
; of any drivers that can be installed by this INF file. It also
; returns the text strings for each driver to be used in the dialog box
; that asks the user to select the driver to install.
;*****************************************************************************
[LanguagesSupported]
ENG
[PlatformsSupported]
PCI
[ReturnOptions]
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;*****************************************************************************
; [InstallOption]
; If the [ReturnOptions] section returns successfully, indicating the
; language is supported, Setup displays a dialog box from which the user
; can select a driver to install. If the user proceeds with the
; installation, Setup calls the [InstallOption] section
;*****************************************************************************
[InstallOption]
;*************************************************************************
; Change "Set !G:DebugOutputControl = 0" to 1 in
; \WINNT\SYSTEM32\NCPASHEL.INF for debug support.
;
; (Unmark the following line to enable debug.)
;Set !G:DebugOutputControl = 1 ;; Debug output {1=turn on, 0=turned off)
;*************************************************************************
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
set LanguageList = ^(LanguagesSupported, 1)
ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "\n"
read-syms ModelConstants
read-syms GeneralConstants
read-syms FileConstants
;read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(FunctionTitle)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
EndWait
Begin = +
Debug-Output "Begin =+ ..."
;*************************************************************************
; Get the version of Windows NT we are installing on.
; We support only Windows NT3.51 & 4.0
;*************************************************************************
set CurrentVersionValue = ""
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(!REG_KEY_READ) KeyNt
ifstr(i) $(KeyNt) != ""
GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
CloseRegKey $(KeyNt)
endif
set TargetVersion = *($(CurrentVersionValue),4)
ifstr $(TargetVersion) == $(NT351VersionConstant)
set DriverFilePath = $(Ndis3FilePath)
else-ifstr $(TargetVersion) == $(NT40VersionConstant)
set DriverFilePath = $(Ndis4FilePath)
else
set Error = "This driver does not support Windows NT version "*($(CurrentVersionValue),4)" !"
goto fatal
endif
Split-String $(SrcDir) "\" SourceList
QueryListSize SLSize $(SourceList)
ifstr *($(SourceList),$(SLSize)) == "\"
set DriverSourcePath = $(DriverFilePath)
else
set DriverSourcePath = "\"$(DriverFilePath)
endif
;*************************************************************************
; Check install mode
;*************************************************************************
Debug-Output "NTN_InstallMode: "$(!NTN_InstallMode)
Debug-Output "NTN_RegBase: "$(!NTN_RegBase)
Debug-Output "ProductKeyName: "$(ProductKeyName)
ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Debug-Ouput "Cannot configure the driver software."
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else
set StartLabel = configureadapter
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
set from = $(fatal)
set to = $(fatal)
goto $(StartLabel)
installadapter =+
Debug-Output "installadapter =+ ..."
Debug-Output "NTN_RegBase: "$(!NTN_RegBase)
Debug-Output "ProductKeyName: "$(ProductKeyName)
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
set OldVersionExisted = $(TRUE)
Debug-Output "Older version existed !!"
endif
StartWait
;*************************************************************************
; Enumerate our device.
;*************************************************************************
Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R0) == {}
set Error = $(CANNOT_FIND_ANY_CARD)
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
set AdapterList = $($R0)
Debug-Output "AdapterList: "$(AdapterList)
Debug-Output " "
Debug-Output "!STF_CWDDIR: "$(!STF_CWDDIR)
;*************************************************************************
; Install driver for our device.
;*************************************************************************
ifint $(OldVersionExisted) == $(FALSE)
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
endif
Set SrcDir = $($R1)
endif
install "Install-Option"
install "Install-Cfg"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
;*************************************************************************
; Check to see if the product Software key exists already in the system
; service keys before we try to add the software component.
;*************************************************************************
Debug-Output "NTN_ServiceBase: "$(!NTN_ServiceBase)
Debug-Output "ProductHardwareName: "$(ProductHardwareName)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(ProductHardwareName) $(!REG_KEY_READ) KeyNt
CloseRegKey $(KeyNt)
Ifstr(i) $(KeyNt) == ""
Debug-Output "No root service exist, try to AddSoftwareComponent"
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
Set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
Debug-Output "AddSoftwareComponent success!"
set NewValueList = {{SoftwareType, $(NoTitle),$(!REG_VT_SZ), $(SoftwareType)},+
{MajorVersion, $(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion, $(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title, $(NoTitle),$(!REG_VT_SZ), $(ProductSoftwareTitle)},+
{Description, $(NoTitle),$(!REG_VT_SZ), $(ProductSoftwareDescription)},+
{ServiceName, $(NoTitle),$(!REG_VT_SZ), $(ProductSoftwareName)},+
{InstallDate, $(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Debug-Output "AddValueList to "$(SoftProductKey)"(SoftProductKey)"
Debug-Output $(NewValueList)
Debug-Output " "
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type, $(NoTitle),$(!REG_VT_SZ), $(NetRuleSoftwareType)},+
{use, $(NoTitle),$(!REG_VT_SZ), $(NetRuleSoftwareUse)}, +
{bindform, $(NoTitle),$(!REG_VT_SZ), $(NetRuleSoftwareBindForm)}, +
{class, $(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable, $(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ), $(Option)}}
Debug-Output "AddValueList to "$(SoftNetRuleKey)"(SoftNetRuleKey)"
Debug-Output $(NewValueList)
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
goto fatalregistry
endif
endif
Debug-Output "Begin to install NIC..."
ForListDo $(AdapterList)
set BusNum = *($($),1)
set DeviceNum = *($($),2)
set FunctionNum = *($($),3)
set dbgstr = "BusNum:"$(BusNum)" DevNum:"$(DeviceNum)" FuncNum:"$(FunctionNum)
Debug-Output $(dbgstr)
Debug-Output $(ProductHardwareDescription)
Debug-Output $(ProductHardwareName)
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), +
$(DeviceNum), $(ProductHardwareDescription), $(ProductHardwareName) "YES"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) != "YES"
Debug-Output "AddHardwareComponent: "$(ProductHardwareName)
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
Set AdapterNumber = $($R4)
Set AdapterServiceName = $($R5)
Set NewRegBase = $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)
Debug-Output "AddHardwareComponent success ("$($R4)")"
Debug-Output "NewRegBase = "$(NewRegBase)
;*****************************************************************
; Usually HardNetCardKey is under HLM\SOFTWARE\Microsoft\
; Windows NT\NetworkCards\{#Instance}
;*****************************************************************
set HwDetailDesc = $(ProductHardwareDescription)" [Bus "$(BusNum)" Slot "$(DeviceNum)"]"
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ), $(Manufacturer)},+
{Title, $(NoTitle),$(!REG_VT_SZ), "["$($R4)"] "$(ProductHardwareTitle)},+
{Description, $(NoTitle),$(!REG_VT_SZ), $(HwDetailDesc)},+
{ProductName, $(NoTitle),$(!REG_VT_SZ), $(ProductHardwareName)},+
{ServiceName, $(NoTitle),$(!REG_VT_SZ), $($R5)},+
{InstallDate, $(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
;*****************************************************************
; Usually HardNetRuleKey is under HLM\SOFTWARE\Microsoft\
; Windows NT\NetworkCards\{#Instance}\NetRules
;*****************************************************************
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
;*****************************************************************
; Usually HardParameterKey is under HLM\SYSTEM\CurrentControlSet\
; Services\{ServiceName}\Parameters
;*****************************************************************
set BusTypeNum = 5
set NewValueList = {{AdapterType, $(NoTitle),$(!REG_VT_DWORD),$(AdapterType)},+
{MediaType, $(NoTitle),$(!REG_VT_DWORD),1},+
{BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{AdapterCFID, $(NoTitle),$(!REG_VT_DWORD),$(AsicCFID)},+
{BusNumber, $(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
{SlotNumber, $(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+
{FunctionNumber, $(NoTitle),$(!REG_VT_DWORD),$(FunctionNum)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
;*****************************************************************
; Driver parameters default settings
;*****************************************************************
set NewValueList = {{RxBuffer, $(NoTitle),$(!REG_VT_DWORD),$(RxBuffer)},+
{TxBuffer, $(NoTitle),$(!REG_VT_DWORD),$(TxBuffer)},+
{NoCableIndication,$(NoTitle),$(!REG_VT_DWORD),$(NoCableIndication)},+
{TxStartThreshold, $(NoTitle),$(!REG_VT_DWORD),$(TxStartThreshold)},+
{EnableTagging, $(NoTitle),$(!REG_VT_DWORD),$(EnableTagging)},+
{VLANID, $(NoTitle),$(!REG_VT_DWORD),$(VLANID)},+
{EnableGVRP, $(NoTitle),$(!REG_VT_DWORD),$(EnableGVRP)},+
{FlowControl, $(NoTitle),$(!REG_VT_DWORD),$(FlowControl)},+
; {FlowOnThresh, $(NoTitle),$(!REG_VT_DWORD),$(FlowOnThresh)},+
; {FlowOffThresh, $(NoTitle),$(!REG_VT_DWORD),$(FlowOffThresh)},+
{IFSSelect, $(NoTitle),$(!REG_VT_DWORD),$(IFSSelect)},+
{JumboFrame, $(NoTitle),$(!REG_VT_DWORD),$(JumboFrame)},+
{NetworkAddress, $(NoTitle),$(!REG_VT_SZ), $(NetworkAddress)},+
{ConnectionType, $(NoTitle),$(!REG_VT_DWORD),$(ConnectionType)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
CloseRegKey $(HardParameterKey)
;*****************************************************************
; Ndi parameters settings
;*****************************************************************
LoadLibrary "" $(CfgFileName) hLib
set WRegPath = $(!NTN_ServiceBase)"\"$(AdapterServiceName)"\Ndi\Params\"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "ParamDesc" "Receive Buffers"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "Type" "dword"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "Default" "64"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "Min" "16"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "Max" "256"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "Step" "4"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"RxBuffer" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "ParamDesc" "Transmit Buffers"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "Type" "dword"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "Default" "20"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "Min" "16"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "Max" "64"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "Step" "4"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxBuffer" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"NetworkAddress" "ParamDesc" "Network Address"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"NetworkAddress" "Type" "edit"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"NetworkAddress" "Default" ""
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"NetworkAddress" "LimitText" "12"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"NetworkAddress" "Optional" "1"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"NetworkAddress" "UpperCase" "1"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold" "ParamDesc" "Tx Threshold"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold" "Default" "256"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold\enum" "256" "256"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold\enum" "512" "512"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold\enum" "768" "768"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold\enum" "1024" "1024"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold\enum" "8188" "Store and forward"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"TxStartThreshold" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableTagging" "ParamDesc" "802.1Q/1P VLAN tagging"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableTagging" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableTagging" "Default" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableTagging\enum" "0" "Disabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableTagging\enum" "1" "Enabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableTagging" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "ParamDesc" "VLAN ID"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "Type" "dword"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "Default" "6"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "Min" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "Max" "4094"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "Step" "1"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"VLANID" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableGVRP" "ParamDesc" "GVRP"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableGVRP" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableGVRP" "Default" "1"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableGVRP\enum" "0" "Disabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableGVRP\enum" "1" "Enabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"EnableGVRP" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowControl" "ParamDesc" "Flow Control"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowControl" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowControl" "Default" "1"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowControl\enum" "0" "Disabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowControl\enum" "1" "Enabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowControl" "StringOut" "0"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "ParamDesc" "Flow on threshold"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "Type" "dword"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "Default" "1791"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "Min" "0"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "Max" "2047"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "Step" "1"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOnThresh" "StringOut" "0"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "ParamDesc" "Flow off threshold"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "Type" "dword"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "Default" "0"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "Min" "0"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "Max" "2047"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "Step" "1"
; LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"FlowOffThresh" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect" "ParamDesc" "Inter-Frame Spacing"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect" "Default" "3"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect\enum" "0" "96 bit times"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect\enum" "1" "1024 bit times"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect\enum" "2" "1792 bit times"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect\enum" "3" "4352 bit times"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"IFSSelect" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"JumboFrame" "ParamDesc" "Jumbo Frame Support"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"JumboFrame" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"JumboFrame" "Default" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"JumboFrame\enum" "0" "Disabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"JumboFrame\enum" "1" "Enabled"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"JumboFrame" "StringOut" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType" "ParamDesc" "Connection Type"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType" "Type" "enum"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType" "Default" "0"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType\enum" "0" "AutoSense"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType\enum" "11" "10Mbps Half Duplex"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType\enum" "12" "10Mbps Full Duplex"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType\enum" "13" "100Mbps Half Duplex"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType\enum" "14" "100Mbps Full Duplex"
LibraryProcedure DllExitStr $(hLib) WriteReg $(WRegPath)"ConnectionType" "StringOut" "0"
FreeLibrary $(hLib)
;*****************************************************************
; UNATTENDED installation support
; During UNATTENDED installation, DO NOT show the dialog box to ask the
; user to select options.
;*****************************************************************
ifstr $(!STF_GUI_UNATTENDED) != "YES"
LoadLibrary "" $(CfgFileName) hLib
LibraryProcedure DllExitStr $(hLib) RioConfigNCPA $(NewRegBase)
FreeLibrary $(hLib)
Debug-Output "DllExitStr: "$(DllExitStr)
endif
endif
EndForListDo
EndWait
goto successful
configureadapter =+
Debug-Output "configureadapter =+"
Debug-Output "NTN_RegBase: "$(!NTN_RegBase)
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Goto fatalregistry
Endif
Endif
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Goto fatalregistry
endif
set KeyParameters = $($R2)
Debug-Output "KeyParameters: "$(KeyParameters)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
LoadLibrary "" $(CfgFileName) hLib
LibraryProcedure DllExitStr $(hLib) RioConfigNCPA $(!NTN_RegBase)
FreeLibrary $(hLib)
Debug-Output "DllExitStr: "$(DllExitStr)
ifstr(i) $(DllExitStr) == "CANCEL"
set CommonStatus = STATUS_USERCANCEL
endif
goto successful
bindingadapter =+
Debug-Output "bindingadapter =+"
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Debug-Output "removeadapter =+"
set dbgstr = "NTN_RegBase: "$(!NTN_RegBase)
Debug-Output $(dbgstr)
set dbgstr = "ProductKeyname: "$(ProductKeyName)
Debug-Output $(dbgstr)
set dbgstr = "ProductSoftwareName: "$(ProductSoftwareName)
Debug-Output $(dbgstr)
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
Debug-Output "UpgradSoftware =+"
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Set CommonStatus = STATUS_USERCANCEL
Set Severity = STATUS
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
;*****************************************************************************
; Install Sections
;*****************************************************************************
[Install-Option]
Debug-Output "[Install-Option] section..."
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
ifstr(i) $(TargetVersion) == $(NT40VersionConstant)
AddSectionFilesToCopyList Ndis4File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers
set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(Ndis4Drvr)
else
AddSectionFilesToCopyList Ndis3File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers
set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(Ndis3Drvr)
endif
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Cfg]
set STF_VITAL = ""
AddSectionFilesToCopyList CfgFile-$(Option) $(SrcDir)$(CfgSourcePath) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList CfgFile-$(Option) $(SrcDir)$(CfgSourcePath) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
ifstr(i) $(TargetVersion) == $(NT40VersionConstant)
AddSectionFilesToCopyList Ndis4File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers
else
AddSectionFilesToCopyList Ndis3File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers
endif
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.