(C)Copyright 2003-2007 Marvell(R).
All rights reserved..
===========================================================================
yuknd.txt created 07-Mar-2007
Readme File for yuknd.dos v9.12.2.2 (beta) NDIS2 Driver supporting the
Marvell(R) Yukon(R) Ethernet Controller
This file contains
1 Overview
2 Required Files
3 Installation
4 Operation on dual port controllers
5 Driver Parameters
6 Sample Installation/Configuration
===========================================================================
1 Overview
===========
The driver yuknd.dos is the NDIS2 driver for the Microsoft Network Client
for DOS for the Marvell(R) Yukon(R) Ethernet Controller.
***
2 Required Files
=================
YUKND.DOS the driver
OEMSETUP.INF installation skript
PROTOCOL.INI SAMPLE configuration file
Microsoft Network Client 3.0 for MS-DOS
***
3 Installation
===============
When installing the Microsoft Network Client for DOS follow these steps
to install yuknd.dos:
1. Start the installation of the Microsoft Network Client.
2. When you are prompted to select a network adapter, select
"Network adapter not shown on list below ...".
3. Enter the path where the files yuknd.dos and
oemsetup.inf are located.
4. Select "Marvell(R) Yukon(R) Ethernet Controller".
5. Answer the questions in the following dialogs to best fit your needs.
6. When prompted if the listed options are correct, you should select
"Change Network Configuration".
7. Add the protocols that are needed for your network and configure them
to best fit your needs.
8. Return from the dialog and confirm that the listed options are
correct.
9. Finish the installation of the Microsoft Network Client.
10. If you have more than one network adapter you might want to change
the bus number and device number in the protocol.ini as described
in the next section.
***
4 Operation on dual port controllers
=====================================
The driver will run on that port that first came up with a link when the
driver is loaded. It does not switch if the current port loses its link
and the other comes up.
If none of the ports has a link at the time the driver is loaded, it will
setup port A in case a cable is plugged in after loading the driver.
***
5 Driver Parameters
====================
After the installation of the driver, the file protocol.ini in your
Microsoft Network Client installation directory contains the following
lines:
[MRVL$yuknd]
DriverName = yuknd$
When you have more than one adapter supported by the driver in your system
you might want to specify which adapter should be used. There are two ways
to specify the adapter.
Bus and device number (optional)
BUSNUM = <busnum>
DEVNUM = <devnum>
With these parameters you can specify the network adapter the
driver should bind on.
The bus and device numbers are assigned by the BIOS at boot time.
Connection type (optional)
CONTYPE = <contype>
This parameter can be used to force link speed and duplex mode.
Using other values than AUTO turns off auto-negotiation and is not
recommended.
Possible values are:
AUTO
_100FD
_100HD
_10FD
_10HD
Check link mode (optional)
CHECKLINK = 1
When this parameter has been specified the driver uses the first
supported adapter in the system with a valid link. This parameter
will be ignored when BUSNUM and DEVNUM are used.
Number of receive and transmit buffers (optional)
MAXRECEIVES
MAXTRANSMITS
Possible values: 1..3, but the sum of receive and transmit buffers
cannot be greater than 4.
These parameters specify how many transmit and receive buffers the
driver shall use. Using more buffers might improve the performance
but the driver will consume more memory.
Designated port (optional)
HWPORT = A
Possible values: A, B, L(default)
On controllers with two ports, the driver will use the port that is
selected (Port A or B) or it will use the port that has a link.
On controllers with only one port, this parameter will be ignored and
defaults to 'A'.
If the parameter CHECKLINK is selected at the same time, the parameter
PORT is automatically reset to 'L'.
Adjust internal behavior (optional)
FIX = <bitmask>
A bitmask to change some internal behavior of the driver. May be
entered as a number (e.g. 3) or as a bitstring (e.g. "011").
- Bit 0 ("FIX=1") avoids crashes caused by a stack overflow
problem (observed only with MtTool 3.0). Use only if you
experience crashes or system stops.
- Bit 1 ("FIX=2") will let the driver queue packets internally.
MS network client 3.11 with IPX (nwlink) may otherwise stop
working if out of send buffers.
Bit values can be combined by simply using their sum (e.g. "FIX=3").
***
6 Sample Installation/Configuration
====================================
Below you find a sample protocol.ini and system.ini from the Microsoft
Client Installation directory:
Sample system.ini:
[network]
filesharing=no
printsharing=no
autologon=yes
computername=MyComputer
lanroot=C:\NET
username=Me
workgroup=MyWorkgroup
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=MyWorkgroup
preferredredir=basic
autostart=basic
maxconnections=8
[network drivers]
netcard=yuknd.dos
transport=tcpdrv.dos,nemm.dos
devdir=C:\NET
LoadRMDrivers=yes
[386enh]
TimerCriticalSection=5000
UniqueDosPSP=TRUE
PSPIncrement=2
[Password Lists]
*Shares=C:\NET\Shares.PWL
Sample protocol.ini:
[network.setup]
version=0x3110
netcard=MRVL$yuknd,1,MRVL$yuknd,1
transport=tcpip,TCPIP
lana0=MRVL$yuknd,1,tcpip
[TCPIP]
NBSessions=6
SubNetMask0=255 255 0 0
IPAddress0=10 9 1 41
DisableDHCP=1
DriverName=TCPIP$
BINDINGS=MRVL$yuknd
LANABASE=0
[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP
[MRVL$yuknd]
DriverName=yuknd$
CHECKLINK=1
*** End of Readme file ***
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.