--------------------------------------------------------------------
README.TXT
Dell RAID Controllers: U320 SCSI Raid 0 or 1
CERC SATA 1.5/6ch
CERC SATA 1.5/2s
PERC 320/DC
NOTE: Not all controllers support all RAID
levels and operating systems.
RAID Storage Manager
as of February 3, 2005
--------------------------------------------------------------------
The following information is available in this README file:
1. Documentation
2. General Cautions and Notes
2.1 General Cautions
2.2 General Notes
3. Array Level-Specific Notes
3.1 RAID 10 Notes
4. Controller-Specific Compatibility Issues
4.1 SATA Controllers
5. RAID Storage Manager Notes
6. Operating System-Specific Issues and Notes
6.1 Windows
6.2 Linux
--------------------------------------------------------------------
1. Documentation
- RAID Storage Manager Online Help
--------------------------------------------------------------------
2. General Cautions and Notes
2.1 General Cautions
- While an array is being built or cleared, DO NOT remove and
reinsert any drive from that array. Doing so may cause
unpredictable results for any of the controller's arrays.
- While a drive is being cleared, DO NOT try to include it in a
new array. Doing so may cause unpredictable results.
- DO NOT move drives containing an array or volume from one
controller to another while the power is on. Doing so could
cause the loss of the array configuration or data, or both.
Instead, power off both affected controllers, move the drives,
and then restart.
2.2 General Notes
- When displaying information on a physical device, the device,
vendor and model information may be displayed incorrectly.
- During array migration from a RAID 1 or RAID 5 to a RAID 0, if
the original array had a spare drive attached, the resulting
RAID 0 retains the spare drive.
- After using a hot spare to successfully rebuild a redundant
array, information about the hot spare drive may not display
as expected. RAID Storage Manager may continue to display
it as a global hot spare.
--------------------------------------------------------------------
3. Array Level-Specific Notes
3.1 RAID 10 Notes
- Performing a Verify and Verify/Fix on a RAID 10 displays the
same message text in the event log, "Build/Verify started on
second level array of array 'Array_0.'" You may see the message
three times for a Verify, but only once for a Verify/Fix.
- During a migration from a RAID 0 to any redundant array like
RAID 1, 5, or 10, RAID Storage Manager shows the status as
"Degraded Reconfiguring" for a moment, then the status changes
to "Reconfiguring." The "Degraded" status does not appear in the
event log.
--------------------------------------------------------------------
4. Controller-Specific Compatibility Issues
4.1 SATA Controllers
- A Clear operation on an array may have a performance impact
on other processes, such as Build/Verify processes, involving the
same array members. Therefore, Dell recommends that you NOT
attempt any other operations while performing a Clear operation
on a SATA array.
--------------------------------------------------------------------
5. RAID Storage Manager Notes
- You can run RAID Storage Manager under all supported
operating systems.
- The blink LED feature is supported only in SAF-TE enabled
enclosures.
- Performing a Verify and Verify/Fix on a RAID 10 displays the same
message text in the event log, something like, "Build/Verify
started on second level array of array 'Array_0.'" You may see the
message three times for a Verify, but only once for a Verify/Fix.
- Task priority is not retained after rebooting. If you change
a priority to LOW or MEDIUM, and reboot, the controller resets the
priority to the default (HIGH).
- When initializing a new array on a HostRAID controller
(eg, CERC SATA 1.5/2s), you cannot change the task priority to
HIGH. The event log indicates that the priority is changed;
however, it actually remains at its previous setting.
- When an array fails, the array name returns to its default name.
- If the RAID Storage Manager detects a change in your network
connection from connected to disconnected, or vice-versa, you
may see a message that the RAID Storage Manager Agent needs to
be restarted.
To restart the agent under Windows:
1. Go to My Computer->Manage->Services
2. Select RAID Storage Manager Agent
3. Click Restart
To restart the agent under Linux, type:
/etc/init.d/stor_man.sh restart
--------------------------------------------------------------------
6. Operating System-Specific Issues and Notes
6.1 Windows
- Formatting a logical volume using the My Computer function
may result in an incomplete format which would necessitate
a reformat. WORKAROUND: Use Windows Disk Management/Manager.
6.2 Linux
- This release supports the following Linux distributions:
° Red Hat Enterprise Linux AS 2.1
° Red Hat Enterprise Linux AS 3 and WS 3
° Red Hat Enterprise Linux AS 4 and WS 4
- To run RAID Storage Manager under Red Hat Enterprise Linux 4,
the Standard installation with "Compatibility Arch Support"
is required.
- Before you can install the RAID Storage Manager under Red Hat
Enterprise Linux AS 3 or WS 3, you must install two packages
from Red Hat installation CD:
- compat-libstdc++-7.3-2.96.122.i386.rpm
- compat-libstdc++--devel-7.3-2.96.122.i386.rpm
NOTE: The version string in the file name may be different
from above. Be sure to check the version string on
the Red Hat CD.
For example, type:
rpm --install /mnt/compat-libstdc++-7.3-2.96.122.i386.rpm
where mnt is the mount point of the CD-ROM drive.
- If you cannot connect to a remote RAID Storage Manager
installed on a Linux system, verify that the TCP/IP hosts
file is configured properly.
1. Open the /etc/hosts file.
NOTE: The following is an example:
127.0.0.1 localhost.localdomain localhost matrix
2. If the hostname of the system is identified on the line
with 127.0.0.1, you must create a new host line.
3. Remove the hostname from the 127.0.0.1 line.
NOTE: The following is an example:
127.0.0.1 localhost.localdomain localhost
4. On a new line, type the IP address of the system.
5. Using the Tab key, tab to the second column and enter the
fully qualified hostname.
6. Using the Tab key, tab to the third column and enter the
nickname for the system.
NOTE: The following is an example of a completed line:
1.1.1.1 matrix.localdomain matrix
where 1.1.1.1 is the IP address of the server and
matrix is the hostname of the server.
7. Restart the server for changes to take effect.
--------------------------------------------------------------------
(c) 2004-2005 Dell, Inc. All Rights Reserved.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.