Additional Information
Sound Galaxy Stellar 6X MM Kit V 1.10
This file contains additional information and changes about the
various software that was not available at printing time.
Win95 driver Installation for Sound Card
========================================
1. Start the Windows 95 program. Click on the <Start> button on the bottom
taskbar, select <Setting> from the menu and click on the <Control Panel>
selection.
2. Select <Add New Hardware> under Control Panel menu. Click on the <Next>
button and select <No> from "Add New Hardware" the screen and click on
the <Next> button again. Adjust the scroll bar to "Sound,video and game
Controllers" menu line and select it.
3. Click on the <Next> button, followed by the <Have Disk> button. You will
be prompted to insert Driver disk into A:\.
4. You should insert the sound card Audio Disk #1 into the Drive A: (B:)
and path it to \WIN95 directory drive to continue the installation of
the Windows 95 16-bit audio drivers. This will end the sound card drivers
installation.
5. To make use of the WaveTable/External MIDI devices and joystick port. You
should proceed to install the drivers for MPU-401 and joystick. To install
these drivers, repeat steps #1 to #2 and shift the scroll bar downward to
select "Microsoft" from the Manufactuers box. A list of drivers will now
be displayed in the "Models:" dialog box. Click on MPU401 & joystick one
at a time to complete the installation.
(Note: MPU-401 & joystick drivers can be found in your Win95 CD-ROM.)
6. Restart the Win95 session to effect the newly installed drivers.
7. If you encounter any conflict after installation, please refer to the
Trouble-shooting section in Win95 for further details.
CD-ROM Drive Support
====================
The bundled CD-ROM device driver supports only on the following drives:
Driver CD-ROM Model
------ ------------
SGIDECD.SYS - Aztech CDA268-03I / CDA268-03ISE / CDA468-01I /CDA668-01I
Using Digital (.WAV) Audio with DOS 6.x's DoubleSpace*
======================================================
The DoubleSpace utility included with DOS 6.x can cause problems
if you attempt to play or record "high data rate" (i.e.: stereo/
44.1kHz/16-bit) digital audio to or from a compressed disk.
Therefore, if you anticipate that you will be playing or recording
a lot of stereo/44.1kHz/16-bit digital audio, you should set up a
non-compressed drive partition and configure the audio application
to use this drive as their Work and Temp directories.
For information on setting up a non-compressed partition for your
hard drive, refer to your DOS 6.x Users Guide.
The same procedure should be followed if you are using Stacker, a
third-party disk compression utility.
Notes About Using EMM386.EXE
============================
When running applications with EMM386.EXE installed, the following
error message may appear:
"EMM386 DMA buffer is too small"
You can overcome this problem in two ways:
- remove the EMM386.EXE entry from the CONFIG.SYS file
OR
- add the following parameter to the EMM386.EXE entry in the
CONFIG.SYS file:
D=64
where D specifies how many kilobytes of memory should be
reserved for buffered Direct Memory Access (DMA).
An example of this may be:
C:\WINDOWS\EMM386.EXE D=64
***********************************************************
* In case you encounter any problem with our products, *
* please quote the following model(s) when calling our *
* Technical Support : *
* Washington 16AB Sound Card *
* Aztech CDA668-01I CD-ROM Drive *
***********************************************************
------- The End ---------
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.