Windows NT
This is an ASCII file called MSNT.TXT in the ATI
CardAssistant \TXT\MS directory. Use a text editor or
word processor with a mono-space font such as Courier
to print this file if needed for reference.
************************************************************
** **
** Installing the NDIS 3 Driver on Windows NT 3.5x or 4.x **
** **
************************************************************
------------------------------------------------------------
-- Contents --
------------------------------------------------------------
I. Special Considerations
II. Files Needed for Installation
III. Installing the Miniport Driver
IV. Removing an Existing Driver
I. Special Considerations
=========================
Configuration of the AT-2400 is under PCI control. For most
applications, no setup other than normal installation of
the network software is necessary.
To view the card's configuration or to run Diagnostics,
use the CardAssistant setup program, SET2400.EXE.
The SET2400 utility only runs on DOS.
If you do not have a DOS boot partition on your Windows NT
drive, boot DOS from floppy.
To de-install the driver, use the remove driver option from
your Windows NT Network Control Panel. See "IV. Removing
an Existing Driver".
II. Files Needed for Installation
=================================
The following files are required for installation:
\A2400.SYS (Driver)
\OEMSETNT.INF (OEM setup file for miniport driver and
Windows NT)
\TXT\MSNT.TXT (This file)
III. Installing the Miniport Driver
===================================
The Windows Miniport (NDIS) driver supports Windows NT 3.51
or later. If you are running version 3.1, you must upgrade
your copy of Windows NT.
If you are installing multiple adapter cards in a single
computer, complete the installation process for each card.
1. If the AT-2400 adapter card is already installed, reboot
into Windows NT. If you have not installed the AT-2400
adapter card into your computer, shutdown the computer,
turn it off and unplug it. Install the card by following
the instructions that came with your computer. Then turn
the computer on again. Boot into Windows NT.
2. NT 3.5x: Double-click the Network icon in the Control
Panel
NT 4.0: Double-click the Network icon in the Control
Panel.
3. NT 3.5x: From the Network Adapter Card drop-down list in
the Add Network Adapter dialog box, choose
"<OTHER> Requires Disk from Manufacturer." Then
click Continue.
NT 4.0: Select the Adapters tab; click the Add button.
From the Select Network Adapter pop-up window,
do not select from the Network Adapter list;
choose the Have Disk button.
5. Insert the CardAssistant diskette into your floppy disk
drive, make sure a:\ appears in the text field and
click OK.
6. Verify that "ATI 2400 Ethernet card" appears in the
Choose OEM Option dialog box. Then click OK.
7. In the Network Settings dialog box, verify that "ATI
2400 Ethernet" card appears in the "Installed
Adapter Cards" list. Then click OK.
8. This completes the card installation. Click OK. Windows
NT prompts you to configure the protocols you will be
using for network communications.
9. From the Network Settings Change dialog box, click
Restart Now.
IV. Removing an Existing Driver
===============================
If any drivers need to be removed from your existing
installation, remove them first, shutdown the NT operating
system and reboot.
1. NT 3.5x: Double-Click the Network icon in the Control
Panel.
NT 4.0: Double-click the Network icon in the Control
Panel.
2. NT 3.5x: From the "Network Settings" dialog box, select
the adapter to remove. Then choose "Remove".
NT 4.0: Select the Adapters tab. Select the adapter to
remove. Then choose "Remove".
3. From the "Network Settings" dialog box, verify that the
selected adapter has been removed from the "Installed
Adapter Cards" list. Then choose "OK".
4. From the "Network Settings Change" dialog box, choose
"Restart Now".
5. After the Windows NT operating system shuts down, turn
the power switch off and on.
6. Log on to Windows NT.
7. Follow the "New or Additional Installation" section of
this file to install your AT-2400 Ethernet Adapter.
* Third-party trademarks are the property of their
respective owners.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.