D-Link Support Publishing \UNIXWARE\README.TXT July 1996
D-Link PCI Family Ethernet Adapter Installation
for UnixWare 2.01
Contents
ÄÄÄÄÄÄÄÄ
Introduction
Requirements
Minimum Skill Level
Compatibility List
Getting Started
Introduction
ÄÄÄÄÄÄÄÄÄÄÄÄ
This installation assumes that the adapter is working properly.
Getting Started will describe the installation instructions.
Requirements
ÄÄÄÄÄÄÄÄÄÄÄÄ
A PCI compatible computer
Novell/SCO UnixWare 2.01
A PCI Family Series Adapter
A knowledge of basic Unixware commands and editing text files
Minimum Skill Level
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
A knowledge of basic UnixWare commands
A knowledge of editing text files
A knowledge of UnixWare basic file structure
A knowledge of the network driver configuration being used
Compatibility List
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Any PCI Family Ethernet Adapter
For a Motherboard compatibility list please consult your local
D-Link Branch Office
Getting Started
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
login UNIX as "root"
login: root
Password: XXXXXX
#doscp a:/unixware/setup setup_dlkpci
#chmod +x setup_dlkpci
#./setup_dlkpci a:/unixware (you can specify another path as you wish)
Install the Driver
#cd /usr/lib/tcprt/dlk
#chmod +x build_dlkpci
#./build_dlkpci
Do you wish to install or delete the network driver(i/d/q)? i
~
/* first adapter install */
Do you want to configure Board_0? (y/n/q) y
~
Board_0 configuring ...
Please enter the IP host name for the device dlkpci_0 (default:xxxx): aaron
~~~~~
Please Initialize the IP Address for host XXXX (default: xxx.xxx.xxx.xxx):
192.9.200.1
~~~~~~~~~~~
Configure host XXXX with default Ethernet(TM) ifconfig option?
Info message is long. (yse no ClassC BerkeleyC info; default: info): y
~
/* the following let you configure DE-530/DFE-500 NICs */
/* If you are configuring board 0 then the following messages will prompt */
/* for specifying the access type of PCI bus */
Note:
The default is to use the PCI BIOS calls (in 32-bit protected
mode). Some systems may not support these calls, in which case
there will be problems at boot time. If using a system that
does not support 32-bit protected mode PCI BIOS calls, direct
hardware accesses must be used.
PCI mechanism 1 or PCI mechanism 2 should be selected depending
on your machine support."
Please specify the way used by PCI to access hardware.........
0. Use 32-bit protected mode PCI BIOS calls."
1. Direct access to the HW, using PCI mechanism 1."
2. Direct access to the HW, using PCI mechanism 2."
Enter number of PCI access type selection (0 1 2) [0] or 'q' to quit: 1
~
PCI access type : Direct access to the HW, using PCI mechanism 1.
Please choose the line speed that you want............
0. Use default value.
1. 10 MB/sec mode.
2. 100 MB/sec mode.
3. Automatic detection between 10 MB/sec and 100 MB/sec mode.
Enter number of line speed selection (0 1 2 3) [0] or 'q' to quit: 3
~
Line Speed : AUTOSENSE_MODE
Please choose the media mode that you want............
0. Use default value.
1. Point to point full duplex twisted pair connection.
2. BNC connection.
3. Twisted pair connection.
4. Automatic detection between TP and BNC.
5. Twisted pair connection with linkfail test ignore & set polarity plus.
Enter number of media mode selection (0 1 2 3 4 5) [0] or 'q' to quit: 4
~
Media Mode : AUTOSENSE_MODE
/* second adapter install */
Do you want to configure Board_1? (y/n/q) y
~
/* the prompts listed above will be repeated */
/* the third adapter */
Repeat the above steps ....
0: dlkpci_0 adapter 0
1: dlkpci_1 adapter 1
2: dlkpci_2 adapter 2
3: dlkpci_3 adapter 3
Select one adapter to support Netware: 0
~
Do you wish to relink the kernel now ? y
~
Note1: The IRQ number must match with the value set in ROM-BIOS before you
specify this value, please check it.
The IRQ for PCI bus can be accessed by pressing [DEL] key when system
is power on and choose the proper select item to set IRQ for PCI bus.
Example: ROM PCI/ISA BIOS (2A4X5C31)
PCI/GREEN FUNCTION SETUP
AWARD SOFTWARE, INC.
Press [DEL] key --> PCI/GREEN FUNCTION SETUP
Slot 3 Using INT# : A-PIRQ1
.
.
.
PIRQ1# Connect IRQ: 5 By Single
~
Note2: After you install DE-530/DFE-500 device driver, you can create a
DeskTop user that has 'root' privilege and using the following
steps:
Admin_Tools -> Networking
-> NetWare_Setup
-> LAN options
-> IPX LAN Device
IPX LAN Frame Type
IPX LAN Device Specifying the device driver for the network
board.
IPX LAN Frame Type Specifying the frame type.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.