1. EVL51004.EXE Driver
2. LMDOS.TXT File Contents

LMDOS.TXT Driver File Contents (EVL51004.EXE)

	 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
	 º                                                   º
	 º     Compex ENET32-VL Ethernet Network Adapter     º
	 º   (C) Copyright PDS, 1995. All Rights Reserved.   º
	 º                                                   º
	 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ


1) INTRODUCTION
===============

This directory contains the following files for installing the
ENET32-VL Ethernet adapter on a DOS LAN Manager workstation.
     
The file layout in the current directory is shown as below:

MSLANMAN.DOS
   |
   |--- LMDOS.DOC       This file
   |___ DRIVERS
	   |
	   |___ ETHERNET
	   |       |
	   |       |___ EN32VL
	   |               |___ EN32VL.DOS
	   |               |___ PROTOCOL.INI
	   |
	   |___ NIF
		 |
		 |_____ EN32VL.NIF


2) NDIS Driver Installation for MS-DOS LAN Manager v2.0 workstation
===================================================================

1.  LAN Manager should already be installed in your
    computer. In the Lan Manager directory, run SETUP.EXE

2.  Select <Actions> from the top menu

3.  Select <Import network drivers> to load the driver.
    Insert the driver diskette into a drive and enter correct
    source drive letter. SETUP will then create the appropriate
    directory and transfer the driver from the diskette.

    After this step, the driver is loaded.  If you want to change the
    existing driver, then you should go through the following steps:

4.  Select <View/Modify> from the top menu.

5.  Select <Network Drivers>. The existing network driver configuration
    and all network adapters and protocols supported are shown.

6.  Remove the existing configuration by choosing <Remove>.

7.  Select "Compex ENET32-VL Ethernet Network Adapter" in the <Network
    Adapter Card> box and choose the apporpriate protocol in the <Protocol>
    box.

8.  Select <Add Driver> to add a hardware driver and <Add Protocol> to
    add a protocol driver to the <Network Configuration> box.

9.  Select <Done> to exit the main menu. Select <Save> from the <Action>
    box to update the changes.


3) NDIS Driver Installation for MS-DOS LAN Manager v2.1/2.2 workstation
=======================================================================

1.  LAN Manager should already be installed in your
    computer. In the Lan Manager directory, run SETUP.EXE

2.  Select <Network Driver> from the <Configuration> menu.

3.  In the configuration window, choose <Add New Config>.

4.  Select <Other Driver>.

5.  Insert driver diskette in the floppy drive A: and press Enter.

6.  Select "Compex ENET32-VL Ethernet Network Adapter". The driver will be
    copied into the Lan Manager.

7.  In the Network Protocol window, you may use Netbeui protocol.

8.  Save the Lan Manager configuration. Exit from Lan  Manager setup.
    Reboot the workstation to make the changes effective.


4.  PROTOCOL.INI FILE
=====================

The keywords used in the PROTOCOL.INI for the ENET32-VL adapter are:

Note: In most cases, it is UNNECESSARY to specify the following keywords.

1.  IOADDRESS

    The I/O address of the adapter. Supported values are 0x220,
    0x240, 0x280, 0x2A0, 0x300, 0x320, 0x340 and 0x380.
    Use this keyword if there are more than one adapter on the
    system and you want to run the driver on a a particular board.
    When it is not specified, the driver will automatically scan for
    the correct I/O address and IRQ value.

2.  INTERRUPT

    The interrupt (IRQ) number of the adapter. Supported values are
    3, 5, 10 and 15.

3.  TXBUFFERS

    The transmit buffer size. A valid value is a number which is a power
    of 2. Default value is 4.

4.  RXBUFFERS

    The receive buffer size. A valid value is a number which is a power
    of 2. Default value is 4.