1. 30kit102.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (30kit102.zip)

	    DE305 DIGITAL EtherWORKS ISA Adapter
	     NDIS Driver Installation Overview
	    ====================================

	 Copyright (C) 1996 by Digital Equipment Corp.
	 All rights reserved.

The driver you need are in the directories MSLANMAN.DOS.
The NDIS drivers contained in this subdirectories are
used with 3Com 3+Open, Microsoft OS/2 LAN Manager OEM
distribution, Release 1.x or 2.x,  and other compatible
OEM versions of LAN Manager.

The drivers named DE305 conform to the Network Driver
Interface Specification (NDIS) defined by Microsoft/3Com.

Included in MSLANMAN.DOS subdirectories are the
following files:

\MSLANMAN.DOS\

	 README.TXT	     This readme File

\MSLANMAN.DOS\DRIVERS\ETHERNET\DE305\

	 DE305.DOS	     The DOS NDIS MAC driver
	 PROTOCOL.INI	     A sample section of PROTOCOL.INI file

\MSLANMAN.DOS\DRIVERS\NIF\

	 DE305.NIF	     Network Information File


Verifying Installation
----------------------

Verify for proper adapter installation by running
the diagnostic program using 1STEP.

Note that only runs under DOS and will not run under
the OS/2 environment.

Sample PROTOCOL.INI Files and Parameters
----------------------------------------

[NDIS2_NIF]

;  Default section of protocol.ini file for the Digital Adapter
    drivername = DE305$
    irq = 3
    iobase = 0x300
; End of this sample file

There are several parameters included in the NDIS2_NIF
section of the PROTOCOL.INI file. However, the only parameter
that you should specify is the "drivername."

If you change other parameter settings, such as the IOBASE
or IRQ, make sure that it matches the hardware setting.
Otherwise, the adapter may fail.

If you don't specify these settings, Digital's NDIS driver
will automatically detect them.

irq	    Specifies the interrupt channel used by the adapter.
	    Acceptable values for this parameter are 2/9, 3, 4, 5,
	    10, 11, 12 ,and 15. However, some of the mentioned Digital
	    adapters do not support all the acceptable values.

iobase	    Specifies the iobase address used by the adapter.
	    This parameter is given in hexadecimal values.
	    Acceptable value for this parameter are 0x200, 0x220,
	    0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0x300, 0x320,
	    0x340, 0x360, 0x380, 0x3a0, 0x3c0, 0x3e0.


List of Additional Parameters in the PROTOCOL.INI file
for the NDIS Driver Configuration
------------------------------------------------------
Note that values for the following parameters are seldom
changed by the user. Most of the time the default
values are used.

Keyword 	Parameter

MaxMultiCast	1 .. 1000  Default 10
		Maximum number of MultiCast Addresses.
		This configures the size of the MultiCast
		Address Table.

MaxRequests	6 .. 64  Default 8
		Maximum number of outstanding General Requests.
		This configures the size of the General Request
		Queue.

MaxTransmits	6 .. 64  Default 12
		Maximum number of outstanding TransmitChain commands.
		This configures the size of the TransmitChain Request
		Queue.

ReceiveChains	6 .. 96  Default 12
		Maximum number of outstanding ReceiveChain commands.
		This configures the size of the ReceiveChain Request
		Queue.

ReceiveBuffers	6 .. 96  Default 12
		Configures the number of the Receive buffers in the
		Receive Buffer Pool.

TransmitBufSize 128 .. 1514  Default 1514
		Configures the size (in bytes) of buffers in the
		Transmit Buffer Pool.

Troubleshooting and Error Messages
----------------------------------

To check for problems, please run the Test Adapter option
from 1Step.

Error Message:
	ERROR: Adapter card not found or I/O port error.
Possible Causes:
	1. The adapter is not installed correctly in its slot.
	2. I/O port failure due to incompatibility between
	   the computer and the card
Solution:
	Run the 1Step program to determine reason for the error.

Error Message:
	DE305-Error-01: Incorrect Media Setting or Bad Transceiver
Possible Causes:
	1. The transceiver failure.
	2. Cable breaks.
	3. Loose cable connection.
Solution:
	Run 1Step's diagnostic program to determine the cause
	of the problem.

---
All trademarks or brand names mentioned are properties
of their respective companies.

-- THE END --