1. 3com3c562x.zip Driver
2. LANSRV.TXT File Contents

LANSRV.TXT Driver File Contents (3com3c562x.zip)

3Com (R)  Corporation 
Installing IBM LAN Server 4.0 for DOS and OS/2  


OS/2
======

This procedure describes how to install  
the NDIS driver for LAN Server 4.0.  OS/2 
must already be installed on your computer.  
To install the NDIS driver for the 3C562 EtherLink III
LAN+Modem PC Card, follow these steps:

1.  Open an OS/2  prompt.

2.  Insert the LAN Server MPTS (Multi-Protocol Transport 
	Services) disk 1 in your diskette 
	drive.  

3.  Make that drive your current drive.  Type: 
	 A: [Enter]

4.  Type:
         Install [Enter]

5.  Select OK.

6.  Select Install.

7.  Select a target drive and then choose OK,

         The default drive is C.

8.  Insert disk 2 when prompted and select OK.

9.  Select OK when the MPTS installation is complete.  

10. Select  Configure.

11. Select LAN Adapters and Protocols 
    and then choose Configure.

12. Select Other Adapters.

13. Insert the 3Com EtherDisk diskette in the 
    diskette drive and enter the drive letter and path to 
    the 3Com NDIS drivers.  For example, type:

         A:\NDIS\OS2

14. Select OK.

15. From the list of Network Adapters, select 
    3Com EtherLink III LAN+Modem PC Card for OS/2 
    and then choose Add. 

16. Under Current Configuration, select 3Com 
    EtherLink III PC Card LAN + Modem for OS/2 and then choose 
    Edit. 

17. Enter the 12-digit address of your EtherLink 
    III LAN+Modem PC Card in the Network Adapter Address 
    box and then choose OK. 

         The address is found on the back of the 
         PC Card following the characters EA=.  

18. Select the protocol(s) you will be using with 
    your network and then choose Add.  

19. Select your protocol(s) under Current 
    Configuration and then choose Edit.

20. Enter the 12-digit address of your 
    EtherLink III LAN+Modem PC Card and then choose OK.  

21. Select  OK. 

22. Select  Close.  

23. Select  Exit.  

24. Select Update CONFIG.SYS and choose Exit.  

25. Select OK.

26. Select Exit.

27. Quit OS/2 and reboot for the changes to take effect.

28. Follow the IBM instructions on installing 
    LAN Server to complete the installation.




DOS
======

IBM DOS Lan Services Install v4.0


1.  Insert the disk labeled "Dos Lan Services Disk 1" into 
	your disk drive.

2.  Change to that drive and type in "INSTALL"

3.  Choose the directory you want the software installed to
  . The default is "C:\NET".

4.  A menu will appear that provides a list of  Network Cards
  . Choose "Network card not shown in the list below..." 

5.  Type in "A:\IBM_40 and remove the "Dos Lan Services Disk 1"
	diskette and insert the EtherDisk.

6.  The next menu should display "3Com 3C562 EtherLink III 
	PC Card.

7.  Additional menus will appear, choose the appropriate options
	for your network environment. Refer to the IBM manual if 
	there are questions regarding these menus.

8.  After completing the installation you must copy ELPC3X.DOS 
	and 3CELCM.EXE to C:\NET before rebooting.



=========================================================
SYSTEM.INI information
=======================
   In order for the modem to function correctly 
in MS Windows, add the following commands to your 
Windows  SYSTEM.INI file under the [386Enh] category:   
(In case they are not there already)

[386Enh]
	 :
	 :
COM1Base=3F8
COM1Irq=4
COM2Base=2F8
COM2Irq=3
COM3Base=3E8
COM3Irq=4
COM4Base=2E8
COM4Irq=3

=========================================================

Please Note
============

 Although the driver name is ELPC3X.DOS, the internal 
 driver name (used in PROTOCOL.INI) is ELPC3$                                  
=========================================================



(%VER NDIS - IBM LAN Server v2.0e)