; ; OEMSETNT.INF ; ; This INF file is used to install LAN adapter driver for Windows NT. ; ; Supported OS: Windows NT 3.51 / NT 4.0 ; Supported Adapters: ; ; D-Link DFE-550TX FAST Ethernet 10/100 Adapter ; ; Usage: ; ; This file is the installation/configuration/deinstallation ; procedure of the driver for Windows NT. It can be called ; from Windows Setup directly, or via the Windows NT Networks ; Control Program Applet (NCPA) from inside the Windows ; Control Panel. ; [Identification] OptionType = NetAdapter [PlatformsSupported] PCI [Options] ALTA [OptionsTextENG] ALTA = "D-Link DFE-550TX FAST Ethernet 10/100 Adapter" [Source Media Descriptions] 1 = "D-Link DFE-550TX Adapter Driver Diskette" [Files-Inf] 2, oemsetnt.inf, SIZE=1000, RENAME=$(!UG_Filename) [Ndis3File-ALTA] 1, DLH5XND3.sys, SIZE=999 [Ndis4File-ALTA] 1, DLH5XND4.sys, SIZE=999 [HelpFile-ALTA] 1, DLH5X.hlp, SIZE=999 ; ; Add by David C.W. Hsieh ; ; These constants are used to detect the version of the target ; Windows NT System and copy related NDIS driver. ; [Model-ALTA] DrvMajorVersion = "2" DrvMinorVersion = "1" Ndis3DrvFileName = "DLH5XND3.SYS" Ndis4DrvFileName = "DLH5XND4.SYS" HelpFileName = "DLH5X.HLP" Ndis3FilePath = "" Ndis4FilePath = "" HelpFilePath = "" ModelCode = "DLH5X" ModelDescription = "DFE-550TX FAST Ethernet 10/100 Adapter" VendorID = 4486 ;; 0x1186 (D-Link) AsicCFID = 268571014 ;; 0x10021186 = 268571014 ; Default parameters TxBuffer = 16 ;; Tx buffers RxBuffer = 16 ;; Rx buffers EnableTagging = 0 ;; Disable VLAN tagging VLANID = 3 ;; Default VLAN ID EnableGVRP = 1 ;; Enable GVRP if tagging enabled. TxStartThreshold = 8188 ;; Store and forward [Model-Common] IHVName = "D-Link" NT351VersionConstant = "3.51" NT40VersionConstant = "4.0" ; ; [ConnectionChoicesALTA] Connect_0 = "AutoSense", 0 Connect_1 = "10Base-T Half Duplex", 1 Connect_2 = "10Base-T Full Duplex", 2 Connect_3 = "100Base-Tx Half Duplex", 3 Connect_4 = "100Base-Tx Full Duplex", 4 [FileConstants] UtilityInf = "UTILITY.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" Manufacturer = $(IHVName)"Corporation" ; ; Driver version information ; ProductMajorVersion = $(DrvMajorVersion) ProductMinorVersion = $(DrvMinorVersion) ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) ProductSoftwareName = $(ModelCode) ProductSoftwareTitle = $(ModelCode)" Adapter Driver" NetRuleSoftwareType = $(ModelCode)"Sys ndisDriver "$(ModelCode)"Driver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """"$(ModelCode)"Sys"" yes no container" NetRuleSoftwareClass = {$(ModelCode)"Driver basic"} NetRuleSoftwareSWBindable = {$(ModelCode)"Driver "$(ModelCode)"Adapter non exclusive 100"} OptionHelpFile = $(HelpFileName) ProductHardwareName = $(ModelCode) ProductHardwareTitle = $(IHVName)" "$(ModelDescription) NetRuleHardwareType = $(ModelCode)" "$(ModelCode)"Adapter" NetRuleHardwareClass = {$(ModelCode)"Adapter basic"} AdapterType = 5 ;; PCI board HelpId = 10 ;; For NoNway Media ;HelpId = 20 ;; For Nway Force media NetRuleHardwareBindForm = " yes yes container" ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" ProductSoftwareDescription = $(IHVName)" "$(ModelDescription)" Driver" FunctionTitle = $(IHVName)" "$(ModelDescription)" Setup" ProductHardwareDescription = $(IHVName)" "$(ModelDescription) ConnectionList = ^(ConnectionChoices$(Option), 1) ConnectionValues = ^(ConnectionChoices$(Option), 2) NoList = ^(NoChoices, 1) NoValues = ^(NoChoices, 2) ShellCodeErrorTitle = "Error: "$(FunctionTitle) ShellCodeErrorText = "Shell Code Error." CANNOT_FIND_ANY_CARD = "Network card is not present in the system" [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 STF_PLATFORM = PPC STF_PLATFORM = Alpha [LanguagesSupported] ENG [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" [FileDependentDlgENG] ;DlgText = "Choose the proper cable type for the "+ ; "network adapter. Select [Help] for a detailled "+ ; "description of the available options of the list." DlgTemplate = "IBMTOK2" DlgType = "RadioCombination" Caption = $(FunctionTitle) Combo1Label = "&Connection Type:" Combo1List = $(ConnectionList) Combo1Out = $(ConnectionValue) ComboListItemsIn = {Combo1List} ComboListItemsOut = {Combo1Out} EditTextLim = 12 EditTextIn = $(NetworkAddress) Edit1Label = "&NetworkAddress" ;CBOptionsGreyed = {} MinHelpId = 10 MaxHelpId = 1140 HelpContext = $(HelpId) [date] Now = {} ? $(!LIBHANDLE) GetSystemDate [Identify] read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) [ReturnOptions] set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) [InstallOption] ; ; Change "Set !G:DebugOutputControl = 0" to 1 in ; \WINNT\SYSTEM32\NCPASHEL.INF for debug support. ; ; Add by David Hsieh ; (Unmark the following line to enable debug.) ;;;Set !G:DebugOutputControl = 1 ;; Debug output {1=turn on, 0=turned off) set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif set-subst LF = "\n" ; ;Read model dependent string, Add by David Hsieh ; read-syms Model-Common read-syms Model-$(Option) ; read-syms GeneralConstants read-syms FileConstants set NetRuleSoftwareBindable = $($R1) read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = "OK" endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set to = Begin set from = Begin set CommonStatus = STATUS_SUCCESSFUL EndWait Begin = + ; ; Get the version of Windows NT we are installing on. ; We support only Windows NT3.51 & 4.0 ; Add by David Hsieh ; set CurrentVersionValue = "" OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(!REG_KEY_READ) KeyNt ifstr(i) $(KeyNt) != "" GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue CloseRegKey $(KeyNt) endif set TargetVersion = *($(CurrentVersionValue),4) ifstr $(TargetVersion) == $(NT351VersionConstant) set DriverFilePath = $(Ndis3FilePath) else-ifstr $(TargetVersion) == $(NT40VersionConstant) set DriverFilePath = $(Ndis4FilePath) else set Error = "This driver does not support Windows NT version "*($(CurrentVersionValue),4)" !" goto fatal endif Split-String $(SrcDir) "\" SourceList QueryListSize SLSize $(SourceList) ifstr *($(SourceList),$(SLSize)) == "\" set DriverSourcePath = $(DriverFilePath) set HelpSourePath = $(HelpFilePath) else set DriverSourcePath = "\"$(DriverFilePath) set HelpSourcePath = "\"$(HelpFilePath) endif ; ; Get NT version Done ; Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo else set StartLabel = configureadapter endif else set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif set from = $(fatal) set to = $(fatal) goto $(StartLabel) installadapter = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) ;;; Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ ;;; $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto end else ;;; Shell $(UtilityInf), CardExistedDlg ;;; ifint $($ShellCode) != $(!SHELL_CODE_OK) ;;; goto ShellCodeError ;;; endif ;;; ifstr(i) $($R1) != "OK" ;;; set CommonStatus = STATUS_USERCANCEL ;;; goto end ;;; endif set OldVersionExisted = $(TRUE) endif Endif ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) install "Install-Hlp" endif Goto installproduct configureadapter = + Ifstr(i) $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Goto fatalregistry Endif Endif Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Goto fatalregistry endif set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) Ifstr(i) $(ValueName) == "ConnectionType" set ConnectionIndex = $(ValueData) else-ifstr(i) $(ValueName) == "NetworkAddress" set NetworkAddress = $(ValueData) endif EndForListDo set ConnectionValue = *($(ConnectionList), ~($(ConnectionValues),$(ConnectionIndex))) ifstr(i) $(ConnectionValue) == "" set ConnectionValue = *($(ConnectionList), 2) endif adapteroptions = + set from = adapteroptions read-syms FileDependentDlg$(!STF_LANGUAGE) SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(HelpId) ui start "InputDlg" ifstr(i) $(DLGEVENT) == "CONTINUE" set ConnectionIndex = $(Combo1Out) set NetworkAddress = *($(EditTextOut),1) ui pop 1 else-ifstr(i) $(DLGEVENT) == "BACK" set CommonStatus = STATUS_USERCANCEL ui pop 1 goto end else ui pop 1 goto end endif set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex))) ifstr(i) $(!NTN_InstallMode) == configure goto updateparameters endif installproduct =+ StartWait set-div DeviceID = $(AsicCFID) 65536 Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R0) == {} set Error = $(CANNOT_FIND_ANY_CARD) set CommonStatus = USER_CANCEL set from = end goto nonfatal endif set AdapterList = $($R0) ifint $(OldVersionExisted) == $(FALSE) Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif ; ; Check to see if the product Software key exists already in the system ; service keys before we try to add the software component. ; OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(ProductHardwareName) $(!REG_KEY_READ) KeyNt CloseRegKey $(KeyNt) Ifstr(i) $(KeyNt) == "" Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) goto fatalregistry endif Set SoftProductKey = $($R1) Set SoftNetRuleKey = $($R2) Set SoftServiceKey = $($R3) Set SoftParameterKey = $($R4) Set SoftLinkageKey = $($R5) set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait goto fatalregistry endif endif ForListDo $(AdapterList) set BusNum = *($($),1) set DeviceNum = *($($),2) set FunctionNum = *($($),3) Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), + $(DeviceNum), $(ProductHardwareDescription), $(ProductHardwareName) "YES" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr $($R0) != "NO_ERROR" set Error = $($R0) goto fatal endif ifstr(i) $($R1) != "YES" Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif set ConnectionIndex = 0 set ConnectionValue = *($(ConnectionList),~($(ConnectionValues),$(ConnectionIndex))) read-syms FileDependentDlg$(!STF_LANGUAGE) SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(HelpId) ; ; UNATTENDED installation support ; During UNATTENDED installation, DO NOT show the dialog box to ask the ; user to select options. ; ; Add by David Hsieh ; ifstr $(!STF_GUI_UNATTENDED) != "YES" ui start "InputDlg" ifstr(i) $(DLGEVENT) == "CONTINUE" set ConnectionIndex = $(Combo1Out) set NetworkAddress = *($(EditTextOut),1) ui pop 1 else-ifstr(i) $(DLGEVENT) == "BACK" set CommonStatus = STATUS_USERCANCEL ui pop 1 goto setfailed else ui pop 1 goto setfailed endif endif ; set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex))) Set HardNetCardKey = $($R1) Set HardNetRuleKey = $($R2) Set HardParameterKey = $($R3) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set BusTypeNum = 5 set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(AdapterType)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+ {AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$(AsicCFID)},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+ {RxBuffer,$(NoTitle),$(!REG_VT_DWORD),$(RxBuffer)},+ {TxBuffer,$(NoTitle),$(!REG_VT_DWORD),$(TxBuffer)},+ {EnableTagging,$(NoTitle),$(!REG_VT_DWORD),$(EnableTagging)},+ {VLANID,$(NoTitle),$(!REG_VT_DWORD),$(VLANID)},+ {EnableGVRP,$(NoTitle),$(!REG_VT_DWORD),$(EnableGVRP)},+ {TxStartThreshold,$(NoTitle),$(!REG_VT_DWORD),$(TxStartThreshold)}} Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}} Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif CloseRegKey $(HardNetCardKey) CloseRegKey $(HardNetRuleKey) set NewValueList = {{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+ {SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+ {FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNum)}} Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList) CloseRegKey $(HardParameterKey) endif EndForListDo EndWait goto successful updateparameters =+ set HardParameterKey = $($R3) set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)}} Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif CloseRegKey $(KeyParameters) goto successful bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end UpgradeSoftware = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} CloseRegKey $(KeyProduct) else goto fatalregistry endif goto end successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif nonfatalinfo = + Set CommonStatus = STATUS_USERCANCEL Set Severity = STATUS goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = $(ShellCodeErrorTitle) set STF_MB_TEXT = $(ShellCodeErrorText) set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" ifstr(i) $(TargetVersion) == $(NT40VersionConstant) AddSectionFilesToCopyList Ndis4File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(Ndis4DrvFileName) else AddSectionFilesToCopyList Ndis3File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(Ndis3DrvFileName) endif endif ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif Exit [Install-Hlp] set STF_VITAL = "" AddSectionFilesToCopyList HelpFile-$(Option) $(SrcDir)$(HelpSourcePath) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" AddSectionFilesToCopyList HelpFile-$(Option) $(SrcDir)$(HelpSourcePath) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) ifstr(i) $(TargetVersion) == $(NT40VersionConstant) AddSectionFilesToCopyList Ndis4File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers else AddSectionFilesToCopyList Ndis3File-$(Option) $(SrcDir)$(DriverSourcePath) $(!STF_WINDOWSSYSPATH)\drivers endif set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exitDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.