iwpriv ================= This is detailed explanation of each parameters for iwpriv. Before reading this document, make sure you already read README. ------------------------------------------------------------------------------------------------------- USAGE: iwpriv ra0 set [parameters]=[val] where [parameters] [val] range explaination ----------------- ----------------------- --------------------------------------------- CountryRegion {0~7} Set country region 0: use 1 ~ 11 Channel 1: use 1 ~ 11 Channel 2: use 1 ~ 13 Channel 3: use 10, 11 Channel 4: use 10 ~ 13 Channel 5: use 14 Channel 6: use 1 ~ 14 Channel 7: use 3 ~ 9 Channel SSID {0~z, less than 32 characters} Set SoftAP SSID WirelessMode {0~2} Set Wireless Mode 0:11b/g mixed, 1:11B only TxRate {0~12} Set TxRate 0:Auto, 1:1Mbps, 2:2Mbps, 3:5.5Mbps, 4:11Mbps, 5:6Mbps, 6:9Mbps, 7:12Mbps, 8:18Mbps, 9:24Mbps, 10:36Mbps, 11:48Mbps, 12:54Mbps Channel {1~14} depends on country region Set Channel BGProtection {0~2} Set 11B/11G Protection 0:Auto, 1:Always on, 2:Always off TxPreamble {0~2} Set TxPreamble 0:Preamble Long, 1:Preamble Short, 2:Auto RTSThreshold {1~2347} Set RTS Threshold FragThreshold {256~2346} Set Fragment Threshold TxBurst {0,1} Set TxBurst Enable or Disable 0:Disable, 1:Enable TurboRate {0,1} Set TurboRate Enable or Disable 0:Disable, 1:Enable AdhocModeRate {0, 1} Set Adhoc mode tx rate 0: adhere WIFI spec., 1: violate WIFI spec. (802.11g WIFI spec disallow OFDM rates in 802.11g ADHOC mode) NetworkType {Infra,Adhoc} Set Network type AuthMode {OPEN,SHARED,WPAPSK} Set Authentication mode EncrypType {NONE,WEP,TKIP,AES} Set Encryption Type DefaultKeyID {1~4} Set Default Key ID Key1 {5 ascii characters or Set Key1 String 10 hex number or 13 ascii characters or 26 hex numbers} Key2 {5 ascii characters or Set Key2 String 10 hex number or 13 ascii characters or 26 hex numbers} Key3 {5 ascii characters or Set Key3 String 10 hex number or 13 ascii characters or 26 hex numbers} Key4 {5 ascii characters or Set Key4 String 10 hex number or 13 ascii characters or 26 hex numbers} WPAPSK {8~63 ASCII or 64 HEX characters} WPA Pre-Shared Key ApClient {0,1} Set ApClient mode 0:Disable, 1:Enable Examples =================================================================== ------------------------------------------------------------------------------------------------------- Example I: Config STA to link with AP which is OPEN/NONE(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=OPEN 3. iwpriv ra0 set EncrypType=NONE 4. iwpriv ra0 set SSID="AP's SSID" Example II: Config STA to link with AP which is SHARED/WEP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=SHARED 3. iwpriv ra0 set EncrypType=WEP 4. iwpriv ra0 set Key1="AP's wep key" 5. iwpriv ra0 set DefaultKeyID=1 6. iwpriv ra0 set SSID="AP's SSID" Example III: Config STA to link with AP which is WPAPSK/TKIP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPAPSK 3. iwpriv ra0 set EncrypType=TKIP 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key" 6. iwpriv ra0 set SSID="AP's SSID" Example IV: Config STA to link with AP which is WPAPSK/AES(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPAPSK 3. iwpriv ra0 set EncrypType=AES 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key" 6. iwpriv ra0 set SSID="AP's SSID" Example V: Config STA to create/link as adhoc mode 1. iwpriv ra0 set NetworkType=Adhoc 2. iwpriv ra0 set AuthMode=OPEN 3. iwpriv ra0 set EncrypType=NONE 4. iwpriv ra0 set SSID="Adhoc's SSID" iwlist ================= This is detailed explanation of each parameters for iwlist. ------------------------------------------------------------------------------------------------------- iwlist ra0 scanning ; list the result after scanning(site survey)Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.