1. ENLGA-1320.zip Driver
2. NWODIDOS.TXT File Contents

NWODIDOS.TXT Driver File Contents (ENLGA-1320.zip)

   Workstation for DOS ODI Client

   Introduction:
   -------------
   This document describes the procedure to setup the NetWare v3.X , v4.X
   v5.x workstation driver for Gigabit Ethernet Network Adapter/Fiber Gigabit
   Ethernet Network Adapter.

   Location of Driver:     \DOSODI\TC902X.COM

   Sample Configuration Files:
   ---------------------------
     STARTNET.BAT:
         LSL
         TC902X
         IPXODI
         NETX or VLM (VLM's for NetWare 4.x )

     NET.CFG:
         LINK DRIVER TC902X

         FRAME Ethernet_802.2 --Specify frame type
         FRAME Ethernet_802.3
         FRAME Ethernet_SNAP
         FRAME Ethernet_II

         AUTOSENSE          ;Performs Power-Up Autosense on all types of boards
                            ;in order to connect to the active line,
                            ;and dynamic autosensing (at run-time) on boards 
                            ;Supporting it.

      ----------------------------------------------------------
      Gigabit Ethernet Network Adapter Support keyword is
      ----------------------------------------------------------

      ;  10BaseT_NWAY       ;Select 10Mbps half duplex NWAY mode.
      ;  10BaseTFD_NWAY     ;Select 10Mbps full duplex NWAY mode.
      ;  100BaseTX_NWAY     ;Select 100Mbps half duplex NWAY mode.
      ;  100BaseTXFD_NWAY   ;Select 100Mbps full duplex NWAY mode.
      ;  VLANId 1           ;Select VLAN ID.  (Decimal Value)
                            ;The valid range is 1 to 4094 
                            
      ----------------------------------------------------------
      Fiber Gigabit Ethernet Network Adapter Support keyword is
      ----------------------------------------------------------

      ;  1000BASEXFD        ;Select 1000Mbps "Fiber" full duplex Force mode.
      ;  VLANId 1           ;Select VLAN ID.  (Decimal Value)
                            ;The valid range is 1 to 4094 

         NetWare DOS Requester
           FIRST NETWORK DRIVE = F
           NETWARE PROTOCOL = NDS BIND
           PREFERRED SERVER = NW412


   Setup Procedures for NetWare 3.11/3.12 Client :
   -----------------------------------------------
      Before you start with the installation process, make sure that
      the  adapter is properly installed and configured. Make sure
      that your NetWare workstation is properly installed.

      1. Copy TC902X.COM from the Gigabit Ethernet Network Adapter/Fiber
         Gigabit Ethernet Network Adapter Driver Diskette subdirectory
         A:\DOSODI to your harddisk.

      2. Create a batch file, or add to your STARTNET.BAT file the commands
         listed above under STARTNET.BAT

      3. Edit the NET.CFG file that you copied over. Edit the file per your
         requirements (see examples above).  If there are two frame types
         listed, whichever frame type is listed first, that is the one that
         the  driver will load.  See above for examples.  The NET.CFG file
         should be in the same directory with the LSL.COM file.


   Setup Procedures for NetWare 4.X Client with vlm:
   -----------------------------------------------
      The  installation utility  INSTALL.EXE  is  located on NetWare's
      "Workstation for DOS" disk. Run INSTALL.EXE from the Workstation
      for DOS Disk.

      The NetWare Client Install program screen will appear.  You must
      complete each of the questions.  These options are specific to your
      needs.

      1. Enter the destination directory for the NetWare Client.
         (The default directory is C:\NWCLIENT).

      2. Gives you the option to automatically update the CONFIG.SYS
         and the AUTOEXEC.BAT files or modify them at a later time
         manually.

      3. Do you wish to install support for MS Windows ? (Y/N)
         (MS Windows Subdirectory: default C:\WINDOWS)

      4. Asks you to select a network driver and provide  configuration
         options.  It uses  the specifications you select to create the
         file NET.CFG. Insert the drivers disk when prompted for the 
         driver disk and specify the driver path A:\DOSODI

      5. Press <Enter> to install


   NOTE:
   -----
         Be sure to add LASTDRIVE=Z to your CONFIG.SYS file for the
         network mappings to work properly.