===========================================================================
WARNING: If you do not read the information presented in this readme file,
you will have problems installing the drivers.
===========================================================================
Advanced Gravis Computer Technology Ltd.
Gravis UltraSound (GF1) Windows 95 Drivers V1.1 (GF195V11.ZIP)
Copyright (C) 1996 by Advanced Gravis Computer Technology Ltd.
All Rights Reserved
===========================================================================
Introduction
------------
These files set up the Windows 95 drivers for the Gravis UltraSound
family of sound cards based on the GF1 chip: UltraSound Classic,
UltraSound MAX and UltraSound ACE. The new UltraSound products based on
the AMD InterWave chip, ie the UltraSound Plug & Play and UltraSound Plug
& Play Pro, come with Windows 95 drivers that are specific to them.
Stay tuned for many more exciting Gravis developments including the newly
shipped UltraSound Plug & Play, UltraSound Plug & Play Pro, Thunderbird,
Mac Firebird (w/new handle), and of course our new 4-player GrIP MultiPort
System with 8-button GrIP-Pads. As you can see its been a very busy year,
and we would like to thank you for your continuing support.
Content
-------
SETUP.EXE GF1 Driver Setup program
FOLDER.EXE Folder update program
SETRSC.EXE Resources setup program
SETUP.BMP
SETUP.INS
_INST32I.EX_
_ISDEL.EXE
_SETUP.DLL
_SETUP.LIB
GRVSULTR.VXD Ring 0 portion of the UltraSound driver
ULTRASND.INF UltraSound setup information file
ULTRASND.DRV UltraSound driver
README.EXE Readme viewer
README. This File
Installation Steps
------------------
The following list of instructions is an addendum to your existing
UltraSound manuals.
1) You need to have your UltraSound card working in DOS. A good way
to verify that you have done this successfully is to run MIDIDEMO
from your UltraSound directory. If you hear music, this means your
MIDI patches and card are configured correctly.
You will also need to record what your UltraSound settings are.
You can do this by typing SET from the DOS prompt. Note the
variable called ULTRASND. There will be a series of 5 numbers after
the equal sign. The numbers are in the following order.
Example: ULTRASND=220,1,1,11,7
Baseport Address, DMA1, DMA2, IRQ1, IRQ2
These settings will be required by Windows 95 for a proper
installation, so be sure to write these down.
2) Load up Windows 95
3) Run SETUP.EXE from the directory where you had unzipped the files,
eg. C:\TEMP (The setup program will guide you through the proper
steps to set up the new GF1 driver).
Hints & Tricks
--------------
1) First thing first. Go back to Step 1 of "Installation Steps".
Ensure that you go through each step.
2) Make sure that you have the following lines in your Autoexec.bat file
EXACTLY as shown (Keep the X's as shown). The SET BLASTER line MUST
contain the usual numbers. Here is a sample UltraSound initialization
section from an AUTOEXEC.BAT:
@SET ULTRASND=XXX,X,X,XX,XX
@SET ULTRADIR=C:\ULTRASND (or whatever directory the
DOS software is installed.)
@SET BLASTER=A220 I7 D1 T1
@SET ULTRA16=XXX,X,X,X,X (UltraSound MAX cards only)
@C:\ULTRASND\ULTRINIT.EXE -ej
Please note that the numeric settings and directory names vary among
machines, and it is very probable that you have a different settings
from the sample section above.
2) When recording from a Mic, Line or CD input, be sure you have set
your recording source correctly. You can get to this in the
UltraSound property sheet from the Control Panel/System applet.
3) Ensure that you are using the same settings in DOS as you are in
Windows 95. This will avoid any conflicts later when running DOS
games under Windows 95.
Troubleshooting
----------------
1) First thing first. Go back to Step 1 of "Installation Steps".
Ensure that you go through each step.
2) If you do not get sounds from a game, try using low IRQ's (i.e 7
and 5). If you still don't get sound, it may be that the game
will not produce sound on the UltraSound card whether a Windows 95
driver is present or not. To be sure, you can unload the driver
and try the game in a DOS Box without drivers. Basically, if the
game doesn't work without a Windows '95 sound driver installed,
there isn't much we can do to help with a sound driver installed.
3) If MIDI music is working but you get no digital (WAV) audio, make
sure you do not have an IRQ or DMA conflict. Using the Control
Panel/System applet, go to the UltraSound property sheet and adjust
the resources to ones that are not in conflict.
4) Win 95 may not show all resource conflicts. If you encounter any
problems, verify that the same settings work under real DOS (not a
DOS box in Win 95).
5) If you don't get sound, make sure that you have disabled "Automatic
Configuration" in the Resources Tab in the device manager for the
Ultrasound.
6) Also be sure that the "Original Configuration (Current)" check box
is checked in the Device Usage section of the General Tab in the
Device Manager.
7) If Windows doesn't boot up for some reason, try booting in safe mode
and then removing the drivers manually. After completing this process
(including rebooting afterward), try re-installing the drivers.
Known Problems
--------------
1) You will not be able to get the UltraSound Mixer and Configuration
utility to work under Windows 95. These are 16-bit applications that
were intended only for Windows 3.x and will not work under Windows 95.
The setup progam will remove the associated icons for these utilities,
so that you will not run them by accident.
2) These drivers do not come with their own midi map configuration.
If you are presented a choice between UltraSound MIDI Synth and MIDI
Mapper, choose UltraSound MIDI Synth, or create your own MIDI Map.
3) Note: In the Windows 95 Volume Control, some controls appear on the
mixer but are not active. This is normal. The Volume Control applet
does not hide the controls that are not supported by the card. As
well, all of the controls may not be visible when the Volume Control
applet is run initially. To enable any of these controls, select
OPTIONS/PROPERTIES in the Volume Control applet, and then enable the
controls you would like to see on the mixer.
4) The option in the Multimedia Options screen entitled "Enable Volume
Control On TaskBar" is not enabled. This is because this function is
for controlling the master volume on the card. Because there is no
master volume hardware on the card, this control is disabled. This
is normal, and is not a defect in the driver.
Bug Reporting and Tech Support
------------------------------
Any problems encountered should be directed to Tech Support, via the
following tech support channels:
Internet: tech@gravis.com
Voice: (604) 431-1807
Fax: (604) 451-9358
Compuserve: GO PCVENB #14 71333,350
[END FILE]
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.