1. pro110c.zip Driver
2. PATHWORK.TXT File Contents

PATHWORK.TXT Driver File Contents (pro110c.zip)

                     PRO110(C) PCI Fast Ethernet Adapters 
	                       NDIS2 MAC Driver
                     for DEC PATHWORK Installation Guide
                    ======================================


The driver named AX8141 contained in the \NDIS20\DOS directory of your Driver
Diskette conforms to the Network Driver Interface Specification (NDIS) defined
by Microsoft/3Com.

Installation Procedure
======================

 1. Insert the DEC PATHWORKS Client Setup diskette #1 into your floppy drive
    (either A: or B:).

 2. Type the following and press <Enter> to bring up the startup menu:

     A:>NETSETUP <Enter>

 3. You'll be asked if your keyboard type is LK250. Select "NO." If you are
    using an LK250 keyboard choose "YES."

 4. Next, you'll be prompted to choose a transport option. Select the "DECNET
    transport option" and press <Enter> to proceed.

 5. Your system will prompt you to insert the DNET TRNSPRT diskette #1 into
    your floppy drive. Follow screen instructions.

 6. Then you'll be prompted to specify a destination drive.

     Type C: or D:.

 7. When asked if you are creating an initial workstation diskette, select "NO."

 8. Type in the node name and address (i.e., node number) in the corresponding 
    field. Then press <Enter>.

 9. Type in the server node name and address (i.e., node number) in the
    corresponding field. Then press <Enter>.

10. When asked to "Select the network adapter type:", choose "Ethernet".

11. When prompted to "Select the network adapter:", choose "Other NDIS".

12. Indicate the directory location of your NDIS driver in the adapter driver
    diskette. For example, type the following:

      A:\NDIS20\DOS\AX8141.DOS
      or
      A:\MSLANMAN.DOS\DRIVERS\ETHERNET\AX8141.DOS

13. When prompted, indicate the directory location of the PROTOCOL.INI file in
    the adapter driver diskette. For example, type the following:

      A:\NDIS20\DOS
      or
      A:\MSLANMAN.DOS\DRIVERS\ETHERNET

14. Select "WRITE KEY DISK" to save the settings that you have chosen. When
    prompted to copy the AX8141.DOS and PROTOCOL.INI files, insert the adapter
    driver program diskette into drive into your floppy drive.

15. Follow screen instructions to complete the installation.

16. From the Configuration screen, press F10 to exit to C:\.

17. Edit the PROTOCOL.INI file from the DECNET sub-directory. Remove the
    semicolon (;) from the statement "NI_IRQ = 5" under the [DATALINK] section.

18. Make sure that the IRQ value in the new [AX8141.DOS] section matches the
    NI_IRQ value in the [DATALINK] statement.


Sample Configuration Files
==========================

1. CONFIG.SYS File

   shell=c:\command.com /P /E:526
   device=c:\decnet\himem.sys
   REM  device=C:\dos\EMM386.EXE ram 1024  ;;do not add EMM386.exe this driver
   dos=high, UMB
   devicehigh=c:\decnet\protman.sys /I:D:\DECNET
   devicehigh=c:\decnet\ethpci.dos
   rem device=c:\decnet\nddrv.sys
   rem device=c:\decnet\npdrv.sys
   FILES=50
   BUFFERS=50
   LASTDRIVE=v
   STACKS=9,256

2. PROTOCOL.INI file for PATHWORKS v4.1

   ; PROTOCOL.INI file create by DNETOMO.V41 V4.1.060
   ; via DNETWIK.V41 V4.1.047

   [PROTOCOL MANAGER]
    DRIVERNAME = PROTMAN$

   [IPX4MAC]
    DRIVER = IPX$MAC
    BINDINGS   = AX8141.DOS

   [DATALINK]
    DRIVERNAME   = DLL$MAC
    LG_BUFFERS   = 16
    SM_BUFFERS   = 6
    OUTSTANDING  = 32
    HEURISTICS   = 0
    BINDINGS   = AX8141.DOS
    ;Specify IRQ level used by workstations network adapter
    NI_IRQ     = 3

   [AX8141.DOS]
    ; PROTOCOL.INI for the PCI Fast Ethernet Adapters
     DriverName = AX8141$
    ; SLOT = 0
    ;; Usage: "Slot=nn"
    ;; Range: 0 - 255.
    ;------------------

    ; CONNECT_MODE = "AUTOSENSE"
    ;; Usage: "CONNECT_MODE=xxx"
    ;; Options: AUTOSENSE, TP, TP_FULL_DUPLEX.
    ;-----------------------------------------
         
    ;LINE_SPEED = "100MB"
    ;; Usage: "LINE_SPEED=xxxx"
    ;; Options: 10MB, 100MB.
    ;-----------------------------------------
    ; End if this sample file 

    Note: If you request 10Mbps speed and Full Duplex mode, please change the 
          statement ;CONNECT_MODE=TP_FULL_DUPLEX and ;LINE_SPEED=10MB which
          inside PROTOCOL.INI and delete its semi-colon. Please change  
          corresponding option for another mode.

3. AUTOEXEC.BAT File

   @Echo off
   Break on
   Cls
   Prompt $p$g
   REM Insert any keyboard internationalization and character set information
   REM here.
   if not exist \decnet\STARTNET.BAT go to nostartup
   Call \decnet\STARTNET
   Goto end
   :nostartup
   @echo ** WARNING ** STARTNET.BAT file not found.  Network functions not
   @echo    performed.