SETUP.TXT Driver File Contents (NA010.zip)

*****************************************************************************
*                                                                           *
*                       PNP ISA ETHERNET ADAPTER                            *
*                                                                           *
*                         SETUP.EXE USER GUIDE                              *
*                                                                           *
*****************************************************************************

The SETUP.EXE program is used to set the adapter's configuration
and diagnose the adapter's hardware.

The most important thing for this PNP ISA adapter is that:
======================================================================
** To use this adapter on Non-PnP machine, please run SETUP.EXE program
and set the adapter to JUMPERLESS mode, otherwise driver can't recognize
the adapter.

** To use this adapter on Non-PnP O.S.(ex. DOS), please enter "PNP AND
PCI SETUP" in the PC CMOS SETUP and set "PNP OS Installed" to "No",
otherwise SETUP.EXE and driver can't recognize the adapter.
======================================================================

Starting the Program
====================

1. From DOS, type the following indicating the directory
   or drive location of the SETUP.EXE program. Then press
   <Enter>:

   A:\SETUP   <Enter>

2. Identify your adapter. Use the up/down arrow keys to
   highlight the appropriate adapter name.

Note
----
If there is more than one adapter installed inside the
host PC, the Hardware Configuration module will prompt
you to specify the card you want to configure. In the
meantime, program will automatically resolve the I/O base
or IRQ conflict, then adjust the available I/O base or
IRQ for the adapter.


View Current Configuration
==========================

1. Use the up/down arrow keys to select the
   "VIEW CURRENT CONFIGURATION" option and press <Enter>
   to view the current adapter's configuration settings.

2. This function displays its configuration to include
   the following items:

   *  Operating Mode
   *  Ethernet Address
   *  Medium Type (AUTO, 10BaseT Link Test Disable, AUI, BNC)
   *  Full-Duplex
   *  I/O Base Address
   *  Interrupt
   *  Boot ROM Base Address

3. Press SPACE BAR key or ESC key to return to the main menu.


Setup
=====

1. Choose "Setup" by highlighting the option using
   the up/down arrow keys. Then press <Enter> to continue
   and set the adapter's configuration by manual.

2. This function displays the following items to set
   available values by manual in different mode:

Plug & Play Mode :

   *  Operating Mode
   *  Medium Type (AUTO, 10BaseT Link Test Disable, AUI, BNC)
   *  Full-Duplex
   *  Boot ROM Base Address

Jumperless Mode :

   *  Operating Mode
   *  Medium Type (AUTO, 10BaseT Link Test Disable, AUI, BNC)
   *  Full-Duplex
   *  I/O Base Address
   *  Interrupt
   *  Boot ROM Base Address

3. If there is any change value for any item, Press ESC key
   and HARDWARE RESET or ENTER key to update value of item.

4. If there is not any change value for any item, Press
   ESC key to return to the main menu.

Note
----
When Boot ROM is enabled in Plug & Play Mode, the Menu will
show the following items to set available values by manual.

   *  Operating Mode
   *  Medium Type (AUTO, 10BaseT Link Test Disable, AUI, BNC)
   *  Full-Duplex
   *  Boot ROM Base Address
   *  |--- Power-up I/O Base
   *  |--- Power-up Interrupt


Run Diagnostics
===============

1. Choose the "Run Diagnostics" option to test the
   adapter's components and its installation and then
   press  <Enter> to continue.

2. The program will run the following tests:

   *    Run EEPROM Test
   *    Run Diagnostics On Board
   *    Run Diagnostics On Network


   Run EEPROM Test
   ---------------
     The program will run READ/WRITE tests on each register in
     the EEPROM.


   Run Diagnostics On Board
   ------------------------
     The program will run the following tests:

           *     Board Reset
           *     I/O Registers
           *     Loop Back Test
           *     Cable Connection
           *     RAM Test

     This test monitors the adapter and corresponding cabling
     system. However, it does not test the network's condition.

     The screen displays the PASSED or FAILED count for each
     test.  If a test fails, press the space bar to display the
     reason for failure and possible solutions.

     The adapter test checks the following items ---

     *   Board Reset Test checks the initial status of the
         Ethernet Controller
     *   I/O Registers Test checks I/O accessibility
     *   Loop Back Test checks adapter's controller
     *   Cable Connection Test checks the network link
     *   RAM Test checks the condition of on-board RAM


   Run Diagnostics On Network
   --------------------------
     - The program will thoroughly verify your adapter's ability
       to communicate with another device on the network.

     - Set up at least one computer as a Responder and at least
       one as an Initiator.

     - The Responder displays the status of communications with
       each Initiator on the network.

     - The Initiator displays the current Responder and the
       status of corresponding communications.


-----
All trademarks or brand names mentioned are properties
of their respective companies.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 0.76