INI_VERSION=9.3 #--------------------------------------------------------------------------------- # This script file configures Model 180 VSAT to operate on # # GE-4 8MB production chain (HSP 76, HPP 25) # # Created by Boris Reifman on 12/05/2000 boris.reifman@starband.com # # Modification History: # # 12/08/00 - B. Reifman - Changed outbound_id hex value to all lower case letters # 01/17/01 - G. Folsom - Changed outbound frequency and START frequency #--------------------------------------------------------------------------------- # # See HOWTO.ini file for a detailed description of each parameter and a # script language. # prelabel=SBD CONFIGURATION=SBD 9_26_00 INI_MINUTES=0 PGM_MINUTES=0 INPUT_TYPE=ZIPCODE HUB_LATITUDE=39.00 N HUB_LONGITUDE=77.00 W SATELLITE_POSITION=101.0 W BACKUP_HUB_LATITUDE=41.85N BACKUP_HUB_LONGITUDE=87.65 W BACKUP_SATELLITE_POSITION=101.0 W TIMEOUT=120 TIME_SLOT_DURATION=34548 INBOUND_RATE=1536 OUTBOUND_RATE=8192000 endprelabel # # The programming script begins here # start set usat_group_address "8191" set outbound_rate "8192" set outbound_rate_test "8192" set outbound_modulation "Q" set outbound_reed_solomon "Y" set time_slot_duration "34548" set outbound_id "10ef" set out_code_rate_1/4 "N" set out_code_rate_n/4 "2" set out_code_rate_n/4_test "1/2" set interleaver_id "0" set establish_link "Y" set inbound_modulation "M" set inbound_rate_ra "153600" set dual_inbound_rate "N" set inbound_reed_solomon "N" set inbound_convolution "Y" set inbound_ra_frame_length "442" set inbound_da_frame_length "442" set k_for_inb_coding "7" set hpp_id "25" set hsp_link_number "63" set load_probe "N" set installation_password "123" set main_outbound_frequency "1237" set main_channel_delay "" set main_inbound_reference_frequency "1237560" set main_inbound_idle_frequency "0" set number_of_day_inbound_bands "1" set day_inbound_band_1_start_frequency "1242840" set day_inbound_band_1_stop_frequency "1249800" set number_of_night_inbound_bands "1" set night_inbound_band_1_start_frequency "1242840" set night_inbound_band_1_stop_frequency "1249800" set inbound_initial_frequency "1246200" set inbound_initial_offset "" set backup_outbound_frequency "1237" set backup_channel_delay "" set backup_inbound_reference_frequency "1237560" set backup_inbound_idle_frequency "0" set number_of_backup_day_inbound_bands "1" set backup_day_inbound_band_1_start_frequency "1242840" set backup_day_inbound_band_1_stop_frequency "1249800" set number_of_backup_night_inbound_bands "1" set backup_night_inbound_band_1_start_frequency "1242840" set backup_night_inbound_band_1_stop_frequency "1249800" set backup_inbound_initial_frequency "1246200" set hsp_port_for_wagers "63" set hsp_port_for_management "63" # These parameters are assumed by default set port_configuration "02" set enable_dial_backup "N" set port_mode "1" set dial_backup_speed "2400" set primary_dial_backup_number "" set secondary_dial_backup_number "" set enable_download "N" set enable_high_concentration_mode "N" set da_time-slots "2" set usat_group2_address "20" set hardware_version "" set support_high_speed_inbound_mode "Y" calculate_delays beep set inbound_initial_offset "0" # Remove the pound sign (#) in the next line to ask for the INBOUND INITIAL OFFSET #loadv inbound_initial_offset "Please enter the Inbound Initial Offset" status "Turn on switches 1, 7 and 8 on the IDU" status "then turn the IDU power ON . . . " message "Turn the IDU power ON . . . " TIMEOUT 0 loop_begin loop_waitfor "... " sendcr loop_continue loop_waitfor "> " sendcr loop_continue loop_waitfor "(Y/N)" sendcr loop_continue loop_waitfor "RPP simulator is active" message "Please wait while erasing flash . . ." status "Erasing flash" pause 3 send "20" loop_break loop_end waitfor "Please enter ..." send "1" waitfor "from sector" send "1" waitfor "to sector" send "15" waitfor "Please enter ..." send "8" pause 1 send "22" status "Setting defaults" case "-> USAT OWN ADDRESS" address "Enter the terminal SERIAL number" send-serial label address TIMEOUT 5 waitfor "< 128 .. 16382 > " send "499068" case "Enter the terminal SERIAL number" serial "Set TEST frequencies" test-freq label test-freq waitfor "< Y/N > ... " send "N" label serial saveserial# "[" "]" waitfor "(decimal) ... " send "0" loop_begin loop_waitfor "... " sendcr loop_continue loop_waitfor "> " sendcr loop_continue loop_waitfor "(Y/N)" sendcr loop_continue loop_waitfor "RPP simulator is active" message "Please wait while the IDU resets . . ." pause 3 send "22" loop_break loop_end TIMEOUT 60 status "Reseting IDU..." waitfor "Enter the terminal SERIAL number" label send-serial TIMEOUT 5 waitfor "(decimal) ... " sendserial# waitfor "Enter HARDWARE version" waitfor "(hex) ... " sendcr waitfor "-> USAT OWN ADDRESS" waitfor "< 128 .. 16382 > " sendhex "03" status "Setting parameters..." # waitfor "-> USAT OWN ADDRESS" # waitfor "> " # send "3921000" set satellite "" set satellite2 "" loop_begin loop_waitfor "MAIN satellite parameters:" set satellite "MAIN" set satellite2 "MAIN" loop_continue loop_waitfor "BACKUP satellite parameters:" set satellite "BACKUP" set satellite2 "BACKUP" loop_continue loop_waitfor "DAY parameters: (of MAIN satellite)" set satellite "MAIN_DAY" loop_continue loop_waitfor "NIGHT parameters: (of MAIN satellite)" set satellite "MAIN_NIGHT" loop_continue loop_waitfor "DAY parameters: (of BACKUP satellite)" set satellite "BACKUP_DAY" loop_continue loop_waitfor "NIGHT parameters: (of BACKUP satellite)" set satellite "BACKUP_NIGHT" loop_continue loop_waitfor "Set Gtech RPP application" waitfor "(Y/N)" send "Y" loop_continue loop_waitfor "Set Gtech RPP default parameters" waitfor "(Y/N)" send "Y" message "Please wait while the defaults are loaded . . ." loop_continue loop_waitfor "Modify existing RPP parameters" waitfor "(Y/N)" send "Y" loop_continue loop_waitfor "-> USAT OWN ADDRESS" waitfor "> " sendidu# loop_continue loop_waitfor "-> USAT GROUP ADDRESS" waitfor "> " sendv usat_group_address loop_continue loop_waitfor "-> OUTBOUND RATE" waitfor "> " sendv outbound_rate loop_continue loop_waitfor "-> OUTBOUND REED SOLOMON" waitfor ">" sendv outbound_reed_solomon loop_continue loop_waitfor "-> OUTBOUND MODULATION" waitfor "> " sendv outbound_modulation loop_continue loop_waitfor "-> TIME-SLOT DURATION" waitfor ": " sendv time_slot_duration loop_continue loop_waitfor "-> INBOUND CONVOLUTION" waitfor ">" sendv inbound_convolution loop_continue loop_waitfor "-> INBOUND RA FRAME LENGTH" waitfor ":" sendv inbound_ra_frame_length loop_continue loop_waitfor "-> INBOUND DA FRAME LENGTH" waitfor ":" sendv inbound_da_frame_length loop_continue loop_waitfor "-> OUTBOUND ID" waitfor "> " sendv outbound_id loop_continue loop_waitfor "-> OUT CODE RATE 1/4" waitfor "< Y/N > " sendv out_code_rate_1/4 loop_continue loop_waitfor "-> OUT CODE RATE n/4" waitfor ">" sendv out_code_rate_n/4 loop_continue loop_waitfor "-> INTERLEAVER ID" waitfor ">" sendv interleaver_id loop_continue loop_waitfor "-> ESTABLISH LINK" waitfor "< Y/N > " sendv establish_link loop_continue loop_waitfor "-> INBOUND MODULATION" waitfor "< M/D > " sendv inbound_modulation loop_continue loop_waitfor "-> SUPPORT HIGH SPEED INBOUND MODE" waitfor "< Y/N > " sendv support_high_speed_inbound_mode loop_continue loop_waitfor "-> INBOUND RATE RA" waitfor "> " sendv inbound_rate_ra loop_continue loop_waitfor "-> K FOR INB CODING" waitfor "> " sendv k_for_inb_coding loop_continue loop_waitfor "-> HPP ID" waitfor ">" sendhppid# loop_continue loop_waitfor "-> HSP LINK NUMBER" waitfor ">" sendv hsp_link_number loop_continue loop_waitfor "-> LOAD PROBE" waitfor ">" sendv load_probe loop_continue loop_waitfor "-> DUAL INBOUND RATE" waitfor "> " sendv dual_inbound_rate loop_continue loop_waitfor "-> INBOUND REED SOLOMON" waitfor ">" sendv inbound_reed_solomon loop_continue loop_waitfor "-> Enter installation PASSWORD : " sendv installation_password loop_continue loop_waitfor "Do you want to change password" waitfor "> ... " send "N" loop_continue loop_waitfor "-> HSP port for wagers" waitfor "> " sendv hsp_port_for_wagers loop_continue loop_waitfor "-> HSP port for management" waitfor "> " sendv hsp_port_for_management loop_continue loop_waitfor "-> Port configuration" waitfor "> " sendv port_configuration loop_continue loop_waitfor "-> Enable dial backup" waitfor "< Y/N > " sendv enable_dial_backup loop_continue loop_waitfor "Port mode" waitfor "pulse > " sendv port_mode loop_continue loop_waitfor "Dial backup speed" waitfor " > " sendv dial_backup_speed loop_continue loop_waitfor "Primary dial backup number" waitfor "#* > " sendv primary_dial_backup_number loop_continue loop_waitfor "Secondary dial backup number" waitfor "#* > " sendv secondary_dial_backup_number loop_continue loop_waitfor "Enable download" waitfor "< Y/N > " sendv enable_download loop_continue loop_waitfor "-> Enable high concentration mode" waitfor "< Y/N > " sendv enable_high_concentration_mode loop_continue loop_waitfor "-> DA Time-Slots" waitfor "> " sendv da_time-slots loop_continue loop_waitfor "-> USAT Group 2 Address" waitfor "> " sendv usat_group2_address loop_continue loop_waitfor "Set RSP default parameters" waitfor "(Y/N)" send "Y" loop_continue loop_waitfor "-> OUTBOUND frequency" waitfor "> (MHz) " IF_EQUAL satellite "MAIN" sendv main_outbound_frequency IF_END IF_EQUAL satellite "BACKUP" sendv backup_outbound_frequency IF_END loop_continue loop_waitfor "-> channel DELAY" waitfor "> (x 0.1mSec) " IF_EQUAL satellite "MAIN" senddelay# IF_END IF_EQUAL satellite "BACKUP" sendbackupdelay# IF_END loop_continue loop_waitfor "-> inbound REFERENCE frequency" waitfor "> (KHz) " IF_EQUAL satellite "MAIN" sendv main_inbound_reference_frequency IF_END IF_EQUAL satellite "BACKUP" sendv backup_inbound_reference_frequency IF_END loop_continue loop_waitfor "-> inbound IDLE frequency" waitfor "> (KHz) " IF_EQUAL satellite "MAIN" sendv main_inbound_idle_frequency IF_END IF_EQUAL satellite "BACKUP" sendv backup_inbound_idle_frequency IF_END loop_continue loop_waitfor "-> NUMBER of inbound bands" waitfor "> " IF_EQUAL satellite "MAIN_DAY" sendv number_of_day_inbound_bands IF_END IF_EQUAL satellite "MAIN_NIGHT" sendv number_of_night_inbound_bands IF_END IF_EQUAL satellite "BACKUP_DAY" sendv number_of_backup_day_inbound_bands IF_END IF_EQUAL satellite "BACKUP_NIGHT" sendv number_of_backup_night_inbound_bands IF_END loop_continue loop_waitfor "START frequency" waitfor "> " IF_EQUAL satellite "MAIN_DAY" sendv day_inbound_band_1_start_frequency IF_END IF_EQUAL satellite "MAIN_NIGHT" sendv night_inbound_band_1_start_frequency IF_END IF_EQUAL satellite "BACKUP_DAY" sendv backup_day_inbound_band_1_start_frequency IF_END IF_EQUAL satellite "BACKUP_NIGHT" sendv backup_night_inbound_band_1_start_frequency IF_END loop_continue loop_waitfor "STOP frequency" waitfor "> " IF_EQUAL satellite "MAIN_DAY" sendv day_inbound_band_1_stop_frequency IF_END IF_EQUAL satellite "MAIN_NIGHT" sendv night_inbound_band_1_stop_frequency IF_END IF_EQUAL satellite "BACKUP_DAY" sendv backup_day_inbound_band_1_stop_frequency IF_END IF_EQUAL satellite "BACKUP_NIGHT" sendv backup_night_inbound_band_1_stop_frequency IF_END loop_continue loop_waitfor "-> inbound INITIAL frequency" waitfor "> (KHz) " IF_EQUAL satellite2 "MAIN" sendv inbound_initial_frequency IF_END IF_EQUAL satellite2 "BACKUP" sendv backup_inbound_initial_frequency IF_END loop_continue loop_waitfor "-> inbound initial OFFSET" waitfor "> (KHz) " sendv inbound_initial_offset loop_continue loop_waitfor "RPP simulator is active" send "22" message "Please wait while the IDU resets . . ." loop_break loop_end #TAM changed this from 10 to 60 TIMEOUT 60 status "Reseting IDU..." waitfor "PARAMETERS SETTING PROCESS : SN = " status "Verifying parameters..." TIMEOUT 5 testserial# set satellite "" set satellite2 "" loop_begin loop_waitfor "MAIN satellite parameters:" set satellite "MAIN" set satellite2 "MAIN" loop_continue loop_waitfor "BACKUP satellite parameters:" set satellite "BACKUP" set satellite2 "BACKUP" loop_continue loop_waitfor "DAY parameters: (of MAIN satellite)" set satellite "MAIN_DAY" loop_continue loop_waitfor "NIGHT parameters: (of MAIN satellite)" set satellite "MAIN_NIGHT" loop_continue loop_waitfor "DAY parameters: (of BACKUP satellite)" set satellite "BACKUP_DAY" loop_continue loop_waitfor "NIGHT parameters: (of BACKUP satellite)" set satellite "BACKUP_NIGHT" loop_continue loop_waitfor "Set Gtech RPP application" waitfor "(Y/N)" send "Y" loop_continue loop_waitfor "Set Gtech RPP default parameters" waitfor "(Y/N)" send "N" loop_continue loop_waitfor "Modify existing RPP parameters" waitfor "(Y/N)" send "Y" loop_continue loop_waitfor "-> USAT OWN ADDRESS" waitfor "(" testidu# waitfor "> " sendcr loop_continue loop_waitfor "-> USAT GROUP ADDRESS" waitfor "(" testnv usat_group_address waitfor "> " sendcr loop_continue loop_waitfor "-> OUTBOUND RATE" waitfor "(" testnv outbound_rate_test waitfor "> " sendcr loop_continue loop_waitfor "-> OUTBOUND REED SOLOMON" waitfor "(" testv outbound_reed_solomon waitfor ">" sendcr loop_continue loop_waitfor "-> OUTBOUND MODULATION" waitfor "(" testv outbound_modulation waitfor "> " sendcr loop_continue loop_waitfor "-> TIME-SLOT DURATION" waitfor "(" testv time_slot_duration waitfor ": " sendcr loop_continue loop_waitfor "-> INBOUND CONVOLUTION" waitfor "(" testv inbound_convolution waitfor ">" sendcr loop_continue loop_waitfor "-> INBOUND RA FRAME LENGTH" waitfor "(" testv inbound_ra_frame_length waitfor ":" sendcr loop_continue loop_waitfor "-> INBOUND DA FRAME LENGTH" waitfor "(" testv inbound_da_frame_length waitfor ":" sendcr loop_continue loop_waitfor "-> OUTBOUND ID" waitfor "(" testv outbound_id waitfor "> " sendcr loop_continue loop_waitfor "-> OUT CODE RATE 1/4" waitfor "(" testv out_code_rate_1/4 waitfor "> " sendcr loop_continue loop_waitfor "-> OUT CODE RATE n/4" waitfor "(" IF_EQUAL out_code_rate_n/4 "1" tests "1/4" IF_END IF_EQUAL out_code_rate_n/4 "2" tests "1/2" IF_END IF_EQUAL out_code_rate_n/4 "3" tests "3/4" IF_END waitfor ">" sendcr loop_continue loop_waitfor "-> INTERLEAVER ID" waitfor "(" testv interleaver_id waitfor ">" sendcr loop_continue loop_waitfor "-> ESTABLISH LINK" waitfor "(" testv establish_link waitfor "> " sendcr loop_continue loop_waitfor "-> INBOUND MODULATION" waitfor "(" testv inbound_modulation waitfor "> " sendcr loop_continue loop_waitfor "-> SUPPORT HIGH SPEED INBOUND MODE" waitfor "(" testv support_high_speed_inbound_mode waitfor "> " sendcr loop_continue loop_waitfor "-> INBOUND RATE RA" waitfor "(" testnv inbound_rate_ra waitfor "> " sendcr loop_continue loop_waitfor "-> K FOR INB CODING" waitfor "(" testv k_for_inb_coding waitfor "> " sendcr loop_continue loop_waitfor "-> HPP ID" waitfor "(" testhppid# waitfor ">" sendcr loop_continue loop_waitfor "-> HSP LINK NUMBER" waitfor "(" testnv hsp_link_number waitfor ">" sendcr loop_continue loop_waitfor "-> LOAD PROBE" waitfor "(" testv load_probe waitfor ">" sendcr loop_continue loop_waitfor "-> DUAL INBOUND RATE" waitfor "(" testv dual_inbound_rate waitfor "> " sendcr loop_continue loop_waitfor "-> INBOUND REED SOLOMON" waitfor "(" testv inbound_reed_solomon waitfor ">" sendcr loop_continue loop_waitfor "-> Enter installation PASSWORD : " sendv installation_password loop_continue loop_waitfor "Do you want to change password" waitfor "> ... " send "N" loop_continue loop_waitfor "-> HSP port for wagers" waitfor "(" testv hsp_port_for_wagers waitfor "> " sendcr loop_continue loop_waitfor "-> HSP port for management" waitfor "(" testv hsp_port_for_management waitfor "> " sendcr loop_continue loop_waitfor "-> Port configuration" waitfor "(" testv port_configuration waitfor "> " sendcr loop_continue loop_waitfor "-> Enable dial backup" waitfor "(" testv enable_dial_backup waitfor "> " sendcr loop_continue loop_waitfor "Port mode" waitfor "(" testv port_mode waitfor "> " sendcr loop_continue loop_waitfor "Dial backup speed" waitfor "(" testv dial_backup_speed waitfor "> " sendcr loop_continue loop_waitfor "Primary dial backup number" waitfor "(" testv primary_dial_backup_number waitfor "> " sendcr loop_continue loop_waitfor "Secondary dial backup number" waitfor "(" testv secondary_dial_backup_number waitfor "> " sendcr loop_continue loop_waitfor "Enable download" waitfor "(" testv enable_download waitfor "> " sendcr loop_continue loop_waitfor "-> Enable high concentration mode" waitfor "(" testv enable_high_concentration_mode waitfor "> " sendcr loop_continue loop_waitfor "-> DA Time-Slots" waitfor "(" testv da_time-slots waitfor "> " sendcr loop_continue loop_waitfor "-> USAT Group 2 Address" waitfor "(" testv usat_group2_address waitfor "> " sendcr loop_continue loop_waitfor "Set RSP default parameters" waitfor "(Y/N)" send "N" loop_continue loop_waitfor "-> OUTBOUND frequency" waitfor "(" IF_EQUAL satellite "MAIN" testv main_outbound_frequency IF_END IF_EQUAL satellite "BACKUP" testv backup_outbound_frequency IF_END waitfor "> (MHz) " sendcr loop_continue loop_waitfor "-> channel DELAY" waitfor "(" IF_EQUAL satellite "MAIN" testdelay# IF_END IF_EQUAL satellite "BACKUP" testbackupdelay# IF_END waitfor "> (x 0.1mSec) " sendcr loop_continue loop_waitfor "-> inbound REFERENCE frequency" waitfor "(" IF_EQUAL satellite "MAIN" testv main_inbound_reference_frequency IF_END IF_EQUAL satellite "BACKUP" testv backup_inbound_reference_frequency IF_END waitfor "> (KHz) " sendcr loop_continue loop_waitfor "-> inbound IDLE frequency" waitfor "(" IF_EQUAL satellite "MAIN" testv main_inbound_idle_frequency IF_END IF_EQUAL satellite "BACKUP" testv backup_inbound_idle_frequency IF_END waitfor "> (KHz) " sendcr loop_continue loop_waitfor "-> NUMBER of inbound bands" waitfor "(" IF_EQUAL satellite "MAIN_DAY" testv number_of_day_inbound_bands IF_END IF_EQUAL satellite "MAIN_NIGHT" testv number_of_night_inbound_bands IF_END IF_EQUAL satellite "BACKUP_DAY" testv number_of_backup_day_inbound_bands IF_END IF_EQUAL satellite "BACKUP_NIGHT" testv number_of_backup_night_inbound_bands IF_END waitfor "> " sendcr loop_continue loop_waitfor "START frequency" waitfor "(" IF_EQUAL satellite "MAIN_DAY" testv day_inbound_band_1_start_frequency IF_END IF_EQUAL satellite "MAIN_NIGHT" testv night_inbound_band_1_start_frequency IF_END IF_EQUAL satellite "BACKUP_DAY" testv backup_day_inbound_band_1_start_frequency IF_END IF_EQUAL satellite "BACKUP_NIGHT" testv backup_night_inbound_band_1_start_frequency IF_END waitfor "> (KHz) " sendcr loop_continue loop_waitfor "STOP frequency" waitfor "(" IF_EQUAL satellite "MAIN_DAY" testv day_inbound_band_1_stop_frequency IF_END IF_EQUAL satellite "MAIN_NIGHT" testv night_inbound_band_1_stop_frequency IF_END IF_EQUAL satellite "BACKUP_DAY" testv backup_day_inbound_band_1_stop_frequency IF_END IF_EQUAL satellite "BACKUP_NIGHT" testv backup_night_inbound_band_1_stop_frequency IF_END waitfor "> (KHz) " sendcr loop_continue loop_waitfor "-> inbound INITIAL frequency" waitfor "(" IF_EQUAL satellite2 "MAIN" testv inbound_initial_frequency IF_END IF_EQUAL satellite2 "BACKUP" testv backup_inbound_initial_frequency IF_END waitfor "> (KHz) " sendcr loop_continue loop_waitfor "-> inbound initial OFFSET" waitfor "(" testv inbound_initial_offset waitfor "> (KHz) " sendcr loop_continue loop_waitfor "RPP simulator is active" message "Please wait . . ." loop_break loop_end pause 10 status "Configuration complete. Turn off all switches and disconnect PC." message "Configuration complete. Turn off all switches and disconnect PC." endDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.