1. 10BT2-N.exe Driver
2. WORKGRP.TXT File Contents

WORKGRP.TXT Driver File Contents (10BT2-N.exe)

FILE NAME: WORKGRP.TXT
======================

This file covers the installation procedures for the following networks:

    Microsoft Windows for Workgroups 3.1
    Microsoft Windows for Workgroups 3.11


*******************************************************************************
*  WINDOWS FOR WORKGROUPS 3.1
*******************************************************************************

The Ethernet Card has been designed to be totally compatible with a
conventional NE2000 Ethernet board.  You can either use the NE2000 compatible
driver supplied on your Workgroup disk or Eiger Lab's NE2NDIS driver.


INSTALLING WINDOWS FOR WORKGROUPS FOR THE FIRST TIME
====================================================

1.      Follow the Windows for Workgroups installation procedure.

2.      Select the Drivers option and select the "Add Adapters" button.  
	Highlight "NE2000 compatible Adapter" and press RETURN.

	Alternatively, insert the Ethernet card drivers disk and select
	"Unlisted or Updated Network Adapter".  Indicate the sub-directory
	\NDIS on the drivers disk for the vendor file and you will see
	"EIGER Labs PCMCIA LAN Card" listed in the "Network Adapters" list. 
	Select that option and press RETURN.

3.      Double click on "NE2000 Compatible Adapter" or "Eiger Labs PCMCIA LAN Card"
	or click on "SETUP" to select the required interrupt number (IRQ) and base
	I/O port address. The default is 
		IRQ = 3
		IOBASE = 0x300
	Choose any available option but make sure the Card has the same
	configuration by using EIGERSC.

4.      Continue with the installation.

5.      When installation is complete, you may need to amend your CONFIG.SYS 
	to enable the Card. Copy the file EIGERSC.EXE into the Windows 
	directory and add the line:
		   
		device=c:\windows\EIGERSC.exe
    
	before the line "device=c:\windows\ne2000.dos".


IF YOU HAVE ALREADY INSTALLED WINDOWS FOR WORKGROUPS
====================================================

1.      Select Program Manager and start Control Panel

2.      Goto Step 2 above.



*******************************************************************************
*  WINDOWS FOR WORKGROUPS 3.11
*******************************************************************************

The Ethernet Card has been designed to be totally compatible with a
conventional NE2000 Ethernet board.  You can either use the NE2000 compatible
driver supplied on your Workgroup disk or Eiger Labs's NE2NDIS driver.


INSTALLING WINDOWS FOR WORKGROUPS FOR THE FIRST TIME
====================================================

1.      Run EIGERSC.EXE.

2.      Follow the Windows for Workgroups installation procedure.

3.      The Windows setup software should be able to detect and install the
	correct driver for you.  If the automatic installation failed,
	follow the manual installation procedure below.

4.      When installation is complete, you may need to amend your 
	AUTOEXEC.BAT to enable the Card. Copy the file EIGERSC.EXE 
	into the Windows directory and add the following line before 
	NET START:
		   
		EIGERSC
		NET START


WHEN YOU HAVE ALREADY INSTALLED WINDOWS FOR WORKGROUPS
======================================================

1.      Select Program Manager and run Network Setup from the Networks group.

2.      Select the Drivers option and select the "Add Adapters" button.  
	Highlight "NE2000 compatible Adapter" and press RETURN.

	Alternatively, insert the Ethernet card drivers disk and select
	"Unlisted or Updated Network Adapter".  Indicate the sub-directory
	\NDIS on the drivers disk for the vendor file and you will see
	"EIGER Labs PCMCIA LAN Card" listed in the "Network Adapters" list. 
	Select that option and press RETURN.

3.      Double click on "NE2000 Compatible Adapter" or "Eiger Labs PCMCIA LAN Card"
	or click on "SETUP" to select the required interrupt number (IRQ) and base
	I/O port address. The default is 
		IRQ = 3
		IOBASE = 0x300
	Choose any available option but make sure the Card has the same
	configuration by using EIGERSC.

4.      To use the card, you will need to close Windows and reboot the PC.

4.      When installation is complete, you may need to amend your 
	AUTOEXEC.BAT to enable the Card. Copy the file EIGERSC.EXE 
	into the Windows directory and add the following line before 
	NET START:

		EIGERSC
		NET START