Windows for Workgroups v3.10 Introduction: ------------- This document describes the procedure to install Microsoft Windows for Workgroups v3.10 driver for 10/100 Fast Ethernet PCI adapter. Location of Driver: \WFW31\RTSND.DOS Sample Configuration Files: --------------------------- CONFIG.SYS (install will add these lines) DEVICE=C:\WINDOWS\PROTMAN.DOS /I:C:\WINDOWS DEVICE=C:\WINDOWS\RTSND.DOS *** DEVICE=C:\WINDOWS\MSIPX.SYS (Added if running NetWare) DEVICE=C:\WINDOWS\WORKGRP.SYS LASTDRIVE=P PROTOCOL.INI (install creates this file) [network.setup] version=0x3100 netcard=RTL8139,1,RTL8139 transport=ms$netbeui,MS$NETBEUI *** transport=ms$ipx,MS$IPX (Added if running NetWare) lana0=RTL8139,1,ms$netbeui *** lana0=RTL8139,1,ms$ipx (Added if running NetWare) [protman] DriverName=PROTMAN$ PRIORITY=MS$NETBEUI [RTL8139] ; RTL8139 RPOTOCOL.INI SAMPLE DriverName=RTSND$ EtherID=@52544C111111 ;This keyword is used to desinate a RTL8139 ;adapter by assigning its ethernet ID ;when more than one adapters exist on one ; system. BusNo=@00 ;This keyword is used to desinate a RTL8139 ;adapter by assigning it's PCI bus number ;when more than one adapters exist on one ; system.(must be used with 'DeviceNo' keyword) DeviceNo=@0A ;This keyword is used to desinate a RTL8139 ;adapter by assigning it's PCI Device number ;when more than one adapters exist on one ; system.(must be used with 'BusNo' keyword) Medium Type=AUTO ;This keyword is used to force Ethernet adapter 10HALF ;to medium 10M Half Duplex, 10M Full Duplex 10FULL ;100M Half Duplex,100M Full Dulpex or 100HALF ;Autonigotiation mode 100FULL [MS$NETBEUI] DriverName=netbeui$ SESSIONS=10 NCBS=32 BINDINGS=RTL8139 LANABASE=0 *** [MS$IPX] (Added if running NetWare) *** Drivername=IPX$ (Added if running NetWare) *** MediaType=Novell/Ethernet (Added if running NetWare) *** Bindings=RTL8139 (Added if running NetWare) AUTOEXEC.BAT C:\WINDOWS\NET START *** C:\WINDOWS\MSIPX (Added if running NetWare) *** C:\WINDOWS\NETX (Added if running NetWare) New Windows for Workgroups Installation: ---------------------------------------- 1. When installing Windows for Workgroups, you are prompted for a network driver. Select the "Unlisted or Updated Network Driver". 2. Insert the Ethernet adapter driver disk containing OEMSETUP.INF and RTSND.DOS files. 3. Specify the directory for the driver (A:\WFW31) and select the Adapter driver. 4. Select Advanced options, and make sure the parameters match the card settings. Check keyword "EtherID", which is provided by RTSND.DOS. The installation program copies the necessary files and creates PROTOCOL.INI for use with the adapter. 5. Continue the installation per Windows for Workgroups instructions. Existing Windows for Workgroups Installation: 1. Select the "Control Panel" icon in the Main Group. 2. Select the "Network" icon. 3. Select the "Adapters" button. 4. Select the Add option. 5. Select "Unlisted or Updated Network Adapter" 6. Insert the adapter driver disk with OEMSETUP.INF and RTSND.DOS and specify the path A:\WFW31. 7. Select the 10/100 Fast Ethernet PCI Adapter driver. 8. The installation program copies the necessary files and creates PROTOCOL.INI for use with the adapter. 9. Select "Close" and when prompted, restart computer for changes to take affect and complete the installation. NOTE: You must have a terminated cable attached to the adapter when you start Windows for Workgroups. If you don't, Windows for Workgroups hangs. TO ADD NETWARE: --------------- 1. Select the "Control Panel" icon in the Main Group. 2. Select the "Network" icon. 3. Select the "Networks" button. 4. Select "Novell Netware" and select the add button. 5. Select "OK" and close the Network icon. 6. Select reboot computer and restart Windows. Installing Multiple LAN Adapters: ------------------------------------- There are two different method to complete it: (a) Under DOS mode, you can modify the EtherID or BusNo+DeviceNo keyword field in file C:\WFW31\PROTOCOL.INI. (b) Or you can enter Windows for WorkGroup and follow above setup procedure step 2,then click on "Setup.." button, select "Advanced...",fill EtherID in Value item. Last step to select OK and close NETWORK SETUP.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.