P4S333-M BIOS HPD MISSORI Release Note
==============================================================================
15/02/02 MIS3.04 Release 3.04 directly from MIS3.03A (5E5E)
09/02/02 MIS3.03A (1) Fix Cold Reboot sometimes entering Setup.
(Changed SB watchdog timer from 16ms to 20ms.)
08/02/02 MIS3.03 Release 3.03 directly from MIS3.02B
05/02/02 MIS3.02B Improve S3 Resume Speed by
(1) Re-arrange BIOS Kernel Code
(2) Remove unwanted jumperless Code
01/02/02 MIS3.02A Change System Reset Source from South Bridge to ASUS ASIC
For Agere 1394 PCI Card EEPROM Configuration Read Error Problem
24/01/02 MIS3.02 (1) Fix unreported memory block under XP
(2) Fix Setup Menu in French and Spanish Language,
IDE and ATAPI Device Detecting Strings Show "NONE" Problem.
(3) Revise Setup Multi-Language Strings
20/01/02 MIS3.01 (1) Following MIS3.0B1 to Reduce HDD Detect Pre-waiting time to 1sec for fast cold-boot
(2) Change [VGA Share Memory Default Size] (from 16MB) to 8MB, when total memory is 128MB.
18/01/02 MIS3.0B2 Reduce HDD Detect Pre-waiting time to 2sec to shorten cold-boot time
18/01/02 MIS3.0B1 Reduce HDD Detect Pre-waiting time to 1sec
17/01/02 MIS3.00A (1) Take out Beep Sound in Boot
(2) Fix hynix DIMM, system unstable problem (NB0x5A BIT_5=0)
(3) Fix When insert two infinene DIMMs, S3 fail problem. (NB0xA1)
14/01/02 MIS3.00 Release 3.00 BIOS based on 021B
=======================================================
11/01/02 MIS0.21B Fix Resume from S3, COM2 dead
10/01/02 MIS0.21A Fix WinMe install problem
08/01/02 MIS0.021 (1) Implement INT Rout to E,F,G,H
(2) Fix Cold Reboot abnormally entering Setup.
(Add 8ms more delay to jumpless reset)
(3) Fix when resuming from S3, pressing power buttons twice or more
then system will hang.
07/01/02 MIS0.020 Fix Some AGP VGA Card cannot Resume from S3
04/01/02 MIS0.019 (1) Improve S3 BIOS Resume Time
(2) Fix IDE performance slow problem,when
System Ghosting Image from LAN server under DOS Ghost 7.0
(3) Set IDE Controller Latency Timer to 80h according to SIS's advice
02/01/02 MIS0.018 (1) Revise AC97 Items' CODE to fix MenuItem Bugs
(2) Fix When CMOS Cleared, System cannot Boot from AGP VGA Card
(3) Fix In XP, for some PS2 Mouse resume from S3, system stall for about 30secs.
(4) Revised GPIO Settings
28/12/01 MIS0.017 Revise System Fan Control MenuItems
25/12/01 MIS0.016 (1) Improve S3 Resume time: BIOS Part
(2) Revise System Fan Control Items
1. Set PWM Frequency to 14.318Mhz
2. Rearrange System Fan Control Voltage Items by 6.5V 7V 7.5V ....
(By Increaseing PWM Frequency, the voltage ripple can be reduced
and the readings of Fan speeds in Hardware Monitor are more stable)
(3) Restore [Boot-time Diagnostic Screen] Items and Show Diagnostic Screen
in the form, HP requested.
24/12/01 MIS0.015 (1) Fix When Entering S3 with PS2 Device Acting(Button Pressed or Mouse Moving),
System will hang.
(2) Remove [Boot-time Diagnostic Screen] Item from Setup Menu
(3) In SIS VGA VUMA Set CX11 = 1, to support NEW SiS VGA Driver to Config
TV-Out for NTSC or PAL under Win-OS
20/12/01 MIS0.014 (1) Implement TV Out Function
(2) Fix USB Plug Resume from S3, Plug Device won't work.
(3) Restore MIDI IRQ to 10 and Hide COM Port Selecting Item 2E8/IRQ10
to prevent user use irq10 in COM Port
(4) Upgrade VGA BIOS to 1.05.00 (6520552B.ROM)
19/12/01 MIS0.013 (1) Fix Under XP Ultra DMA HDs Shows working in PIO Mode
(2) Adjust System Fan Control Items to Meet Thermal Spec.
(3) Fix: In BIOS Boot, Shows "Intel Penti... " Bug
(4) Fix When Set COM Port to 2E8/IRQ10 and Enter OS, System
Still Shows it in 3F8/IRQ4 or 2F8/IRQ3. (This is because
the MIDI IRQ is also by default in 10. We move MIDI IRQ to 5)
18/12/01 MIS0.012 Fix System Fan Voltage High too low problem
14/12/01 MIS0.011 (1) Add 48bit LBA Support
(2) Improve S3 Resume Speed by not doing IDE Restore
(3) Fix System Fan Control Menu Items
14/12/01 MIS0.010 Fix S3 Resume USB Keyboard dead problem
12/12/01 MIS0.009 (1) Fix System Fan Control Under Win ACPI OS
(2) Fix Problem When PS2 Mouse exists, System enter S4 will resume automatically
10/12/01 MIS0.008 (1) Implement System Fan Control Function
(2) Fix Setup Menu Item Bugs
(3) Implement Setup Shows CPU FSB, DDR RAM Frequency
(4) Fix S4 RTC, PME Wakeup Problem
05/12/01 MIS0.007 (1) Fix S4 and USB Issue (22-23)
(2) Add UDMA Support for Fast S4 Resume and Speed up HD access under DOS
(3) Fix: In S1, CPU Fan Now active (25)
04/12/01 MIS0.006 (1) Fix Installed Memory Item Showing Style.
Show full memory size
(2) Fix: Can only enter standby once by pressing power button, next time
will reset the system (24)
(3) Fix In Setup Menu,Installed DIMM may be swaped according to SIS stucture.
This may cause incorrect DIMM position shown. this version correct it.
(4) Implement Fan Fault Detection Function (10)
(5) Implement Support for French and Spanish (12)
(6) Fix with PCI VGA Card system would hang. (8)
(7) Fix Some Setup Menu Problems
30/11/01 MIS0.005 (1) Fix the Bug that: When CMOS CheckSum Error,
the BIOS may set VGA share memory size due to the wrong CMOS data.
(2) Add CPU Multiplier MenuItem (3)
29/11/01 MIS0.004 (1) Fix Setup MenuItems (26-36)
(2) Fix PS2 Mouse S3 Resume Automatically Problem (20)
Slow reset-time PS2 mouse caused the problem
(3) Fix S3 Resume, USB mouse stall problem. (21)
(4) Fix DMI dependent show or not show HP logo problem (1)
(5) S3 Wakeup, when USB Plug/unPlug (26)
23/11/01 MIS0.003 Add USB Wake function
22/11/01 MIS0.002 (1) Revised Flash/COM2 Switch Code
(2) Fix S3 Resume Black Screen Problem
(3) Add PS2 Mouse S3 Resume Function
20/11/01 MIS0.001 (1) Revise PCI IRQ Routing
(2) Add System Fan Function (Turn ON at start)
(3) Remove Jumperless Code
14/11/01 MIS0.000 New Project BIOS Created!
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.