README.TXT Driver File Contents (enl832-tx-rent.zip)

   Packet Driver

   Introduction:
   -------------
   This document describes the procedure to setup the Packet driver for
   10/100M PCI Fast Ethernet Adapter.

   Location of Driver:     \SLPKT\SLPKT.COM

   Sample Configuration Files:
   ---------------------------
      AUTOEXEC.BAT
        SLPKT 0x60

   Notes:
   ------
     1.  Load the packet driver using the software interrupt and any
         optional switches if required.

         Usage: SLPKT [options] <packet_int_no> [-medium media type] [bus_no slot_no]

         Example: SLPKT -i 0x60

         The only required  parameter is the software  interrupt.  A packet
         driver needs to have a software interrupt assigned to it for other
         programs to access it. The recommended interrupt 0x60. If you need
         any of the  options  listed below,  place them before the software
         interrupt on the command line.

         -i - Force driver to report itself as 802.3 instead of Ethernet II.
         -d - Delayed initialization.  Used for diskless booting
         -n - NetWare conversion.  Converts 802.3 packets into 8137 packets
         -w - Windows hack, obsoleted by winpkt
         -p - Promiscuous mode disable
         -h - Help
         -u - Uninstall

      2. Media type can be used to force the card to work on specific
         speed and duplex mode. If no media type if specified, then
         driver will read hardware configuration from EEPROM on the
         card.

      3. Type command,SLPKT 0x60, the screen will appear following
         message:

         Full Duplex
         Line Speed 100M
         System: [345]86 processor, PCI bus, Two 8259s
         Packet driver software interrupt is 0x60(96)
         Interrupt number 0xA(10)
         I/O port 0xD800(55296)
         My Ethernet address is 00:E0:20:31:03:02


      4. Installing Multiple LAN Adapters:

         4.1 The user can run SLPKT 0x60 directly, then the screen
             will display :

             Packet driver for 8139 PCI/CARD bus  Fast Ethernet Network 
             Interface Cards, version 1.0
             
             There are 2 Network Cards on your main board :
             Card 1  BusNo=0x00 SlotNo=0x0A IRQ= 0xA  I/O= 0xD800  NodeID= 00:E0:20:31:03:02
             Card 2  BusNo=0x00 SlotNo=0x0B IRQ= 0x5  I/O= 0xDC00  NodeID= 00:E0:20:00:F0:8B
             
             Please select a card No: 1

         4.11 The user just has to select one card from the list. After
             selecting Card 1, the screen will display:
             
             Half Duplex
             Line Speed 100M
             System: [345]86 processor, PCI bus, Two 8259s
             Packet driver software interrupt is 0x60(96)
             Interrupt number 0xA(10)
             I/O port is 0xD800
             My Ethernet address is 00:E0:20:31:03:02

         4.2 The user can use the bus_no and slot_no argument to specify
             the card that you want to select. If bus number is 0x00 and
             the slot number is 0x0B, you just has bo type
             SLPKT 0x60 0x00 0x0B in the command line to select this card
             directly without having to make selection as 4.1.


      5. Installing multiple drivers:

         If you want to install multiple cards each connecting to different
         network, you have to install the driver multiple times, each with
         different packet interrupt number. 



Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.74