PLANET Broadband VPN Router Firmware Release ----------------------------------------------- Router supported : VRT-401S Release date: 03/09/05 Previous Release Version: 1.0 Release 1C New Release Version: 1.0 Release 1D Added Features and Firmware Changes: =================================== a) fix Dyndns service can not be resolved when router reboot or WAN IP has changed. version 1.0 release 1C a) fix router hanging issue version 1.0 release 1B a) fix VPN wizard can not set "Any" at remote IP address. version 1.0 release 1A a) add "Service name" column at PPPoE configuration. version 1.0 release 15 a) fix the bug that can' ping wan ip from different mask. version 1.0 release 14 a) fix the bug that vpn compatibility with pptp. b) change pcdatabase max number to 256. version 1.0 release 13 a) fix VPN hung up when dyn ddns refresh time.(this bug is related to Netscreen remote client problem issue) b) add "any" in "remote ip address" of VPN policy. c) add "enable netbios broadcast" function of VPN policy. version 1.0 release 12 a) fix dtdns don¡¦t work bug b) fix hang up bug when see the internet connection log, which is connecting with ADSL modem with half bridge mode. version 1.0 release 10 a) support NetBUEI can through VPN tunnel b) fix remote management issue version 1.0 release AA a) update VPN kernel b) fix two or more remote access will cause VRT-401S hangup bug c) fix many FTP transfer will not make user can't do any more FTP d) fix use IKE keep alive will make VPN tunnel rebuild every 60 second. version 1.0 release 09 a) Firewall log shows in access control log table b) Fix bug that run FTP under PPPoE will make device hangup c) Fix bug of mac table d) Fix bug that many FTP passive session will make table full e) Firewall log shows in access control log table. f) Config two or more firewall rules with "log always", but only displays the first rules matching issue. g) Select a virtual server, not enable, not select a pc, but it is still added to firewall rules. h) Restore config file with VPN, device will hang up. i) Device will hang up when enable/disable NAT. j) MTU is only up to 1372 though I set MTU 1500. k) Enable syslog ,not include any log type, but logs still show in syslog server. l) Enable/disable "Allow TFTP firmware upgrade" and do TFTP upgrade will cause device hang up. m) Device hang up when doing factory restore ,set pppoe idle time as 0 and configure UPnP. version 1.0 release 04 a) Initial firmware Release. Firmware Upgrade ================ To perform the Firmware Upgrade: a) Please ensure a stable power supply before proceeding firmware upgrade. b) Logon VRT-401S, and find the upgrade menu in Miscellaneous option. Click the "Browse" button and navigate to the location of the firmware file. Select the upgrade file. Its name will be displayed in the Upgrade File field. Click the "Start Upgrade" button to complete firmware upgrade. Please note: After loading firmware to this release (1009), please be sure to refer to the following steps to perform machine default process to activate the new configurations in machine. Following steps can be used to reset configurations on VRT-401S to default state: -------------------------------------------------------------------------- 1. Power off machine, and press the reset button on the rear panel (Reset button is located beside the power plug). 2. Power on machine, do not release the reset button, wait till the red status LED on front panel flashes twice, then release reset button. 3. Use ping command to verify is machine is reset to default configuration (IP address: 192.168.0.1, no logon username/password required ) 4. If there are responses from VRT-401S, use Internet browser to logon VRT-401S and start machine administration. (no logon username/password required ). -------------------------------------------------------------------------- Thanks for choosing PLANET products, any comment or feedback will be appreciated.. Best Regards , PLANET Tech SupportTeam Router Technical support:support_router@planet.com.twDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.