1. FW-GRT401_203.zip Driver
2. FR-GRT401_203.txt File Contents

FR-GRT401_203.txt Driver File Contents (FW-GRT401_203.zip)

PLANET G.SHDSL Router Family Firmware Release
-----------------------------------------------

Router supported : GRT-401
Release date:   	    05/12/14
New Release Version:        2.03(2030C802)
Previous Release: 	    2.02

Added Features and Firmware Changes:
===================================
a) Fix the ping time out issue

ver. 2.02(2020C7A5)
a) Update ATM driver from R3.0.1 to R3.0.5
b) Conserve the last configuration after upgrading software

ver. 2.00(2000C4F5)
a) Fix the issue that PPPoE+NAT, and enable SNMP feature will cause device hanging 

ver. 1.46(146078BD)
a) Add new feature, IEEE 802.1Q VLAN bridge function.

Ver. 1.45(1450786A)
a) Add Netmeeting ALG call-in function under NAT.
b) Fix the bug that Remote Side SNR Margin always shows positive value.
c) To allow the router ping its own interface and get normal reply in console mode.
d) In all UI, modify display info. in item show/system, show MCSV instead of Product Model.
e) Add new feature, DHCP Relay.
f) Add new feature, DHCP client is availabled in LAN interface.
g) Add new feature, PPP client could request fixed IP.
h) Add new feature, ATM QoS rt-VBR and nrt-VBR.
i) Extend the number of remote management hosts from 10 to 16.
j) Add SNMP trap for link up/link down and cold-start.
k) Revise sysObjectID & device group in MIB-II for CID 000/001/009.
l) Revise EOC module for Alcatel 7300 interoperability.
m) Add Logout function in Web-base UI.
n) Add Release and Renew Button for PPP interfaces in item status->wan of Web-base UI.

Ver. 1.42(142076CE)
a) S/W console reset factory default by special account "IAmTheGod" & "ResetFactoryDefault"
b) Customization for customer (011)
c) Fix the bug that ping with full payload length (65530), sometimes got timeout reply.
d) Some of description is modified in WEB UI.

Ver. 1.41(14107674)
a) Fix the bug that Router reboot cause by despiteful packets attack
b) Customization for customer (009)

Ver. 1.40(14007612)
a) Fix the bug that in Web-base UI, can¡¦t accept a network address x.x.x.0 
b) Fix the bug that system hang up cause by 2 (or more) WAN interface use same VCC
c) In Bridge Mode, SNTP always be SyncWithPC Mode
d) Change factory default for SNTP sync period from 1 min. to 1 hr.
e) Fix the bug that user setting may not backup to flash occasionally.

Ver. 1.38(138052EE)
a) Show message ¡§Press Space Key to enter¡K¡¨ in console mode when booting up
b) Fix the bug that Web page some times can¡¦t display properly in Advance/WAN
c) Make the ping request destined to WAN interface from CLI successfully
d) In console mode UI, add foolproof for DHCP IP range setting
e) In console mode UI, if the table of Fixed DHCP Host entry if full, show/script just display 1st entry
f) In console mode UI, change the title of account name to ¡§Name¡¨ to avoid the content of account name display incomplete while default value of account name is over 41 char.
g) Add new feature for configuration Backup/Restore
h) Add new feature, SNTP and virtual server scheduling
i) In WEB UI, STATUS/LAN shows dynamic and fix IP host 
j) Toggle Test LED during RAM test
k) Improve interoperability with Alcatel 7410
l) Fix the bug, ICQ phone and file transfer some times fail
m) Improve compatibility with MSN 5.0 in voice and file transfer
n) In console mode UI, make boot up message shows on home location
o) Fix the bug, status/route shows no WAN port number
p) Add a special trust IP of 0.0.0.0 to allow all host to login manage interface from both LAN and WAN site
q) New feature, STP BPDU packet pass-through
r) Fix the bug, ICMP redirects will be added to routing table
s) Change the default setting of SHDSL type from Annex-A to Annex-B
t) In WEB UI, modify the option items of WAN protocol
u) Fix the bug, in console mode UI just can sets supervisor password, can't sets supervisor name
v) In WEB UI(Console mode UI), ADVANCE/SHDSL(setup/shdsl) disable SNEXT margin, add Current Margin instead of it, and sets the default value to 0 dB.
w) In show/system, model name customization

Ver. 1.36(13605282)
a) Support PPTP/L2TP/IPSec pass-through
b) Support DMZ/Multi-DMZ/Multi-NAT
c) Support ICQ, MSN messenger in NAT, Multi-NAT DMZ and Multi-DMZ mode
d) Fix bug that unicast drop with subneting routing
e) Fix bug that legal IP pool mis-alarm
f) Add feature of SPI firewall
g) PPPoE dynamic IP status 0.0.0.0 added for PPP disconnected
h) Support PPPoE discovery service tag
i) WEB GUI format refined
j) Remove MIB2 ARP set function
k) Fix bug that system some times reboot cause by ARP table overflow
l) Fix the Multicast Storm bug
m) Correct show->config information in console mode
n) Prevent ICQ exception error when receiving bad message
o) VLAN tagged pass-through
p) Fix bug that system might reboot cause by some special length Multi-cast packets from WAN side 
q) Enable IGMP proxy
r) Support the compressed DNS reply
s) Improve DNS proxy efficiency
t) Change factory default for DHCP server from disable to enable
u) Fix bug that possible problem caused from incorrect EoA packet length with FCS
v) Fix bug in WEB-base user interface, check status -> interface the WEB will not response but system is still running
w) Show MCSV in booting information
x) Correct the value of attenuation SHDSL

Ver. 1.22(1220507E)
a) Add lease time setting for DHCP server.
b) Add status¡÷interface command for 2nd layer packet statistics.
c) UI status customization.
d) For SNMP, add RFC-1493 Bridge MIB.
e) In WEB user interface, vendor logo now can be a hyperlink that link to the vendor¡¦s home page.
f) Fix DHCP server bug that Linux workstation can¡¦t get IP.
g) In WEB page, vendor logo customization.
h) UI admin customization

Firmware Upgrade procedures
===================
a) Through webUI: logon GRT via standard web briowser (default username password: root/root), and select "Upgrade" in the "Utility" menu.
Read the screen text carefully, then select the location of firmware file to complete firmware upgrade.
b) Through TFTP:  prepare a TFTP server and allocate firmware file in the folder acknowledged by TFTP server ( this part might be different because of various TFTP server software).
Log on GRT via telnet or console connection (please make sure the communication between GRT and TFTP server is ready to work.) And enable administration mode for firmware upgrade.
Command line screen can be shown below: 

-----------------------------------------------------------------------------
Command Line Window...
admin>enable

Supervisor password: ****

admin#utility upgrade 192.168.0.7 FW-GRT401_203


TFTP server IP address: 192.168.0.7
Upgrade filename: FW-GRT401_203

  Connecting...
  Download
  Byte Transfered :      723954 bytes
  Complete


Transfer Complete, Replace Now? (y/n): y

Writing flash.................. OK!

Do you want to reboot? (y/n): y

-----------------------------------------------------------------------------

Thanks for choosing PLANET products, any comment or feedback will be appreciated.


Best Regards,


PLANET Tech SupportTeam

G.SHDSL router Technical support:support_adsl@planet.com.tw