======================================================================
Server Driver for NetWare 4.X 5.X 6.X
======================================================================
Introduction:
-------------
This document describes the procedure to install the NetWare
server driver for Gigabit Ethernet Network Adapter/Fiber Gigabit
Ethernet Network Adapter.
Location of Driver: \NWSRV\TC902X.LAN
\NWSRV\TC902X.LDI
Contents:
---------
1. File Description
2. Driver Installation for NetWare Server
3. Parameters Description
1. File Description
-------------------
Filename Description
================= =====================================================
README.TXT Presents a summary of the contents for NetWare Server
driver installation.
TC902X.LAN TC902X based 32-bit ODI Driver
This driver complies with NetWare ODI Server driver
SPEC 3.31.
TC902X.LDI The TC902X driver installation file for Netware 6.x/
Netware 5.x/Netware 4.x.
4.X\NBI.NLM NetWare Server 4.X Bus Interface module.
4.X\MSM.NLM NetWare Server 4.X LAN driver Media Support
Module (MSM).
4.X\ETHERTSM.NLM NetWare Server 4.X LAN driver Topology Specific Module
(TSM) for Ethernet.
2. Driver Installation for NetWare Server
-----------------------------------------
** Driver Installation for NetWare Server 4.X **
a. Update Netware Server to 4.2 .
(If dont update to 4.2, use diskette update file "MSM.NLM,
ETHERTSM.NLM")
b. Run NetWare Server System .
c. When the Server prompt appears, load the NetWare Server
Installation Utility ==> "LOAD INSTALL"
d. Select "Driver options" from the "Installtion Options" menu.
e. Select "Configure network drivers" from the "Driver Options" menu.
f. Select "Select a driver" from the "Additional Driver Actions" menu
g. Press <Ins> to install a unlisted driver, then press <F3> to
specify a different path.
h. Insert Driver Diskette in your PC's floppy drive and specify
the path A:\NWSRV\
i. Select "Gigabit/Fiber Gigabit Ethernet Network Adapter" from the
"Select a driver to install:" menu.
j. If necessary, select "Select/Modify driver parameters and
protocols" from the "Board TC902X_1 (Driver TC902X) Actions" memu.
k. Follow instructions to complete driver installation.
** Driver Installation for NetWare Server 5.X/6.X **
a. Run NetWare Server System .
b. When the Server prompt appears, load the NetWare Server
Installation Utility ==> "LOAD NWCONFIG"
c. Select "Driver options" from the "Installtion Options" menu.
d. Select "Configure network drivers" from the "Driver Options" menu.
e. Select "Select a driver" from the "Additional Driver Actions" menu
f. Press <Ins> to install a unlisted driver, then press <F3> to
specify a different path.
g. Insert Driver Diskette in your PC's floppy drive and specify
the path A:\NWSRV\
h. Select "Gigabit/Fiber Gigabit Ethernet Network Adapter" from the
"Select a driver to install:" menu.
i. If necessary, select "Select/Modify driver parameters and
protocols" from the "Board TC902X_1 (Driver TC902X) Actions" memu.
j. Follow instructions to complete driver installation.
Sample AUTOEXEC.NCF for NetWare Server
AUTOEXEC.NCF (one board)
========================
LOAD TC902X SLOT=2 FRAME=ETHERNET_802.2 NAME=TMI_8022
LOAD TC902X SLOT=2 FRAME=ETHERNET_802.3 NAME=TMI_8023
LOAD TC902X SLOT=2 FRAME=ETHERNET_II NAME=TMI_II
LOAD TC902X SLOT=2 FRAME=ETHERNET_SNAP NAME=TMI_SNAP
BIND IPX TMI_8022 NET=10
BIND IPX TMI_8023 NET=20
BIND IPX TMI_II NET=30
BIND IPX TMI_SNAP NET=40
3. Parameter Description
------------------------
The following parameters are used in TC902X.LAN.
a. SLOT : Specifies which adapter is enabled when multiple TC902X based
adapters are found in your computer.
Ex: LOAD TC902X SLOT=3 FRAME=ETHERNET_802.2
LOAD TC902X SLOT=4 FRAME=ETHERNET_II
b. FRAME : Specifies which frame type is used by the driver. Accepted
values are Ethernet_802.2, Ethernet_802.3, Ethernet_II and
Ethernet_SNAP.
Ex: LOAD TC902X FRAME=ETHERNET_802.2
LOAD TC902X FRAME=ETHERNET_802.3
LOAD TC902X FRAME=ETHERNET_II
LOAD TC902X FRAME=ETHERNET_SNAP
c. NODE : Use a different address to replace the node address burned
in EEPROM.
Ex: LOAD TC902X NODE=004095888888
d. SPEED : Specifies which medium type is used by the driver.
----------------------------------------------------------
Gigabit Ethernet Network Adapter Support keyword is
----------------------------------------------------------
Autosense : Auto-Sense media type
10BASET_NWAY : 10Mbps HALF Duplex Nway Mode
10BASETFD_NWAY : 10Mbps FULL Duplex Nway Mode
100BASETX_NWAY : 100Mbps HALF Duplex Nway Mode
100BASETXFD_NWAY: 100Mbps FULL Duplex Nway Mode
----------------------------------------------------------
Fiber Gigabit Ethernet Network Adapter Support keyword is
----------------------------------------------------------
Autosense : Auto-Sense media type
1000BASEXFD : 1000Mbps Fiber FULL Duplex Force Mode
Ex: LOAD TC902X Autosense
e. VLAN : Select VLAN ID. (Decimal Value)
The valid range is 1 to 4094h.
Ex: LOAD TC902X VLANId=1
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.