[Version]=209 M1000::Normally open contact (a contact). This contact is ON when running and it is ON when the status is set to RUN. M1001::Normally OFF contact (b contact). This contact is OFF in running and it is OFF when the status is set to RUN. M1002::ON only for 1 scan after RUN. Initial pulse is contact a. It will get positive pulse in the RUN moment. Pulse width=scan period. M1003::OFF only for 1 scan after RUN. Initial pulse is contact a. It will get negative pulse in the RUN moment. Pulse width=scan period. M1004::On when error occurs M1005::Password of data backup memory card and MPU password don't match M1006::Data backup memory card isn't initial M1007::Data doesn¡¦t exist in the program area of data backup memory card M1008::Monitor timer flag (ON: PLC WDT time out) M1009::When 24VDC is not sufficient that causes LV signal, M1009 will be ON M1010::ES/EX/SS and SC/SA/SX: PLSY Y0 mode selection. It is continuous output when it is ON.EH:PULSE will be output at the END. M1011::10ms clock pulse, 5ms On/5ms Off M1012::100ms clock pulse, 50ms On / 50ms Off M1013::1s clock pulse, 0.5s On / 0.5s Off M1014::1min clock pulse, 30s On / 30s Off M1015::High-speed timer activates M1016::When it is Off, it will display two right-most bits. When it is On, it will display (two right-most bits + 2000). M1017::30 seconds adjustment in RTC M1018::Flag for Radian/Degree, On for degree M1019::Start-up flag of frequency measurement card M1020::Zero flag M1021::Borrow flag M1022::Carry flag M1023::PLSY Y1 mode selection, it is continuous output when it is ON. M1024::COM1 Monitor request M1025::If PLC receive illegal communication request when HPP, PC or HMI connects to PLC, M1025 will be set and save the error code in D1025. M1026::SC/SA/SX and EH: Startup flag of RAMP module M1027::PR output flag M1028::10ms/100ms time switch flag. The base setting flag of T64~T126 is 100ms, when timer is OFF and the base setting flag is 10ms when it is ON. M1029::ES/EX/SS and SC/SA/SX: Pulse output Y0 of PLSY and PLSR command execution completed or other relative command execution completed EH: The first group pulse CH0 (Y0, Y1) output complete executing or other relative command execution completed M1030::ES/EX/SS and SC/SA/SX: Pulse output Y1 of PLSY and PLSR command execution completed EH: The second group pulse CH1 (Y2, Y3) output complete executing M1031::Clear all non-latched memory M1032::Clear all latched memory M1033::Memory latched at STOP M1034::All Y outputs disable M1035::Start X input point to be RUN/STOP switch and correspond to D1035 (for SA models, only X7¡Bfor SX models, only X3¡Bfor SC models, only X5 can be used) M1036::SPD can be used with X0~X5 at the same time to detect starting speed flag (for SCV1.4 or over models) M1039::Constant scan mode M1040::Step transition inhibit M1041::Step transition starts M1042::Start pulse M1043::Zero point return completed M1044::Zero point condition M1045::All outputs clear inhibit M1046::STL state setting (On) M1047::STL monitor enable M1048::Flag for alarm point state M1049::Monitor flag for alarm point M1050::I001 masked M1051::I101 masked M1052::I201 masked M1053::I301 masked M1054::I401 masked M1055::I501 masked M1056::I6 masked M1057::I7 masked M1059::I010~I060 masked M1060::System error message 1 M1061::System error message 2 M1062::System error message 3 M1063::System error message 4 M1064::Operator error M1065::Syntax error M1066::Program error M1067::Program execution error M1068::Execution error locked (D1068) M1070::ES/EX/SS and SC/SA/SX: PWM Y1 output pulse exchange unit, ON for 100us and OFF for 1ms.EH: PWM Y0 pulse exchange unit, ON for 100us (for those after V1.2, pulse exchange unit is decided by D1371), OFF for 1 ms. M1071::PWM Y2 pulse exchange unit, ON for 100us (for those after V1.2, pulse exchange unit is decided by D1372), OFF for 1 ms. M1072::Execute PLC RUN command M1073::System used M1074::System used M1075::FLASH write error M1076::Real time clock error M1077::Battery voltage is too low or malfunction M1078::PLSY command Y0 pulse output stop immediately flag M1079::PLSY command Y1 pulse output stop immediately flag M1080::COM2 Monitor request M1081::FLT command change direction flag M1082::Flag changed for RTC M1083::Enable/Disable execute interrupt program in FROM/TO mode M1086::Set the ON/OFF switch of password function for DVP-PCC01 M1087::LV signal operation flag M1088::Matrix compared flag. If the result is the same, M1088 = 1. If the result is different, M1088 = 0. M1089::Matrix search start flag. Compare from the first bit and M1090=1. M1090::Matrix search start flag. Compare from the first bit and M1090=1. M1091::Matrix finding bit flag. When find it, it will stop comparing and M1091=1. M1092::Matrix pointer error flag. When pointer Pr exceeds this range, M1092=1. M1093::Matrix pointer increases flag. It will add 1 to present pointer. M1094::Matrix pointer clears flag. It will clear present pointer to 0. M1095::Carry flag for matrix rotate/shift output M1096::Complement flag for matric shift input M1097::Direction flag for matrix rotate/shift M1098::Matrix count bit 0 or 1 flag M1099::It is On when matrix count result 0 M1100::A sampling flag of SPD command M1101::To decide whether start file register or not M1102::Y10 end flag of pulse output (SC series models only) M1103::Y11 end flag of pulse output (SC series models only) M1104::SW1 state of DIP switch function card (DVP-F8ID) / AX0 input of 4DI card (DVP-F4IP) (isolated by photocoupler) M1105::SW2 state of DIP switch function card (DVP-F8ID) / AX1 input of 4DI card (DVP-F4IP) (isolated by photocoupler) M1106::SW3 state of DIP switch function card (DVP-F8ID) / AX2 input of 4DI card (DVP-F4IP) (isolated by photocoupler) M1107::SW4 state of DIP switch function card (DVP-F8ID) / AX3 input of 4DI card (DVP-F4IP) (isolated by photocoupler) M1108::SW5 state of DIP switch function card (DVP-F8ID) M1109::SW6 state of DIP switch function card (DVP-F8ID) M1110::SW7 state of DIP switch function card (DVP-F8ID) M1111::SW8 state of DIP switch function card (DVP-F8ID) M1112::AY0 output (transistor output) of 2DO card (DVP-F2OT) M1113::AY1 output (transistor output) of 2DO card (DVP-F2OT) M1115::Start switch for accel/decel pulse output M1116::Acceleration flag for accel/decel pulse output M1117::Target attained frequency flag for accel/decel pulse output M1118::Deceleration flag for accel/decel pulse output M1119::Completed function flag for accel/decel pulse output M1120::COM2(RS-485) Communication protocol holding (communication protocol will be the original setting even if D1120 is changed) M1121::RS-485 Communication data transmission ready M1122::Sending request M1123::Receiving completed M1124::Receiving wait M1125::Communication reset M1126::STX/ETX user/system selection M1127::MODRD/RDST/MODRW instructions. Data receiving is completed, RS instruction doesn’t include. M1129::Receiving time out M1130::STX/ETX selection M1131::MODRD/RDST/MODRW, M1131=On when data convert to HEX M1132::When it is On, it denotes that there is no relative communication instruction in PLC program. M1133::SA/SX: special high-speed pulse Y0 (50kHz) starting flag for outputSCV1.4 or over: synchronous control for two axes, starting flag of Y10 output. M1134::Special high-speed pulse Y0 (50kHz) output. ON for constant output switch (SC doesn¡¦t support) M1135::SA/SX: arrival flag for special high-speed pulse Y0 (50kHz) output number.SCV1.4 or over: synchronous control for two axes, starting flag of Y11 output M1136::COM3 communication protocol holding M1138::COM1 (RS-232) communication protocol holding. D1036 modification invalid after setting. M1139::When SLAVE mode, ASCII/RTU selection for COM1 (RS-232). OFF for ASCII mode and ON for RTU mode. M1140::MODRD/MODWR/MODRW data received error M1141::MODRD/MODWR/MODRW command error M1142::VFD-A command data received error M1143::1.COM2(RS-485) ASCII/RTU mode selections when PLC is SLAVE (it is Off when in ASCII mode and it is On when in RTU) 2.COM2(RS-485) ASCII/RTU mode selections when PLC is MASTER (used with MODRD/ MODWR/MODRW instructions) (it is Off when in ASCII mode and it is On when in RTU mode) M1144::Ouput start switch of accel/decel pulse output function of adjustable slope M1145::Acceleration flag of accel/decel pulse output function of adjustable slope M1146::Target attained frequency flag of accel/decel pulse output function of adjustable slope M1147::Deceleration flag of accel/decel pulse output function of adjustable slope M1148::Complete function flag of accel/decel pulse output function of adjustable slope M1149::Stop counting temporality flag of accel/decel pulse output function of adjustable slope M1150::Declare DHSZ command used for multi-group settings comparison mode M1151::Finish executing multi-group settings comparison mode M1152::Declare DHSZ command used to be frequency control mode M1153::Finish executing frequency control mode M1154::Start designated deceleration function flag of accel/decel pulse output function of adjustable slope M1161::8/16 bits mode (it is On when in 8 bits mode) M1162::Using flag for the integral of decimal system and the floating point of binary systems. ON for the floating point of binary. M1167::HKY input is 16 bits mode M1168::SMOV working mode indication M1169::PWD mode selection M1170::Start executing single step M1171::Execute single step M1172::2-phase pulse output switch (on is start) M1173::On is continuous output switch M1174::Output pulse number attained flag M1178::VR0 potentiometer starts M1179::VR1 potentiometer starts M1184::Startup MODEM M1185::Start to initiate MODEM M1186::Fail to initiate MODEM M1187::Finish initiating MODEM M1188::Display if current MODEM is on-line or not M1196::Number system stting (Off: Dec, On: Hex) (provided for DVP-SX series only) M1197::Display the decimal point at the right-most of number (provided for DVP-SX series only) M1198::Display the decimal point between two digitals (provided for DVP-SX series only) M1199::System used M1200::C200 counting mode (on: count down) M1201::C201 counting mode (on: count down) M1202::C202 counting mode (on: count down) M1203::C203 counting mode (on: count down) M1204::C204 counting mode (on: count down) M1205::C205 counting mode (on: count down) M1206::C206 counting mode (on: count down) M1207::C207 counting mode (on: count down) M1208::C208 counting mode (on: count down) M1209::C209 counting mode (on: count down) M1210::C210 counting mode (on: count down) M1211::C211 counting mode (on: count down) M1212::C212 counting mode (on: count down) M1213::C213 counting mode (on: count down) M1214::C214 counting mode (on: count down) M1215::C215 counting mode (on: count down) M1216::C216 counting mode (on: count down) M1217::C217 counting mode (on: count down) M1218::C218 counting mode (on: count down) M1219::C219 counting mode (on: count down) M1220::C220 counting mode (on: count down) M1221::C221 counting mode (on: count down) M1222::C222 counting mode (on: count down) M1223::C223 counting mode (on: count down) M1224::C224 counting mode (on: count down) M1225::C225 counting mode (on: count down) M1226::C226 counting mode (on: count down) M1227::C227 counting mode (on: count down) M1228::C228 counting mode (on: count down) M1229::C229 counting mode (on: count down) M1230::C230 counting mode (on: count down) M1231::C231 counting mode (on: count down) M1232::C232 counting mode (on: count down) M1233::C233 counting mode (on: count down) M1234::C234 counting mode (on: count down) M1235::C235 counting mode (on: count down) M1236::C236 counting mode (on: count down) M1237::C237 counting mode (on: count down) M1238::C238 counting mode (on: count down) M1239::C239 counter mode setting (on: count down) M1240::C240 counter mode setting (on: count down) M1241::C241 counter mode setting (on: count down) M1242::C242 counter mode setting (on: count down) M1243::C243 counter mode setting (on: count down) M1244::C244 counter mode setting (on: count down) M1245::C245 counter mode setting (on: count down) M1246::C246 counter monitor (on: count down) M1247::C247 counter monitor (on: count down) M1248::C248 counter monitor (on: count down) M1249::C249 counter monitor (on: count down) M1250::C250 counter monitor (on: count down) M1251::C251 counter monitor (on: count down) M1252::C252 counter monitor (on: count down) M1253::C254 counter monitor (on: count down) M1254::C254 counter monitor (on: count down) M1256::System used M1258::Swap Y0 and Y1 pulse output signal M1259::Swap Y2 and Y3 pulse output signal M1260::Let X5 be the reset input signal of all high-speed counter M1261::DHSCR command High-speed comparison flag M1264::HHSC0 Reset function enable M1265::HHSC0 Start function enable M1266::HHSC1 Reset function enable M1267::HHSC1 Start function enable M1268::HHSC2 Reset function enable M1269::HHSC2 Start function enable M1270::HHSC3 Reset function enable M1271::HHSC3 Start function enable M1272::HHSC0 Reset control M1273::HHSC0 Start control M1274::HHSC1 Reset control M1275::HHSC1 Start control M1276::HHSC2 Reset control M1277::HHSC2 Start control M1278::HHSC3 Reset control M1279::HHSC3 Start control M1280::I00¡¼ masked M1281::I10¡¼ masked M1282::I20¡¼ masked M1283::I30¡¼ masked M1284::I40¡¼ masked M1285::I50¡¼ masked M1286::I6¡¼¡¼ masked M1287::I7¡¼¡¼ masked M1288::I8¡¼¡¼ masked M1289::I010 masked M1290::I020 masked M1291::I030 masked M1292::I040 masked M1293::I050 masked M1294::I060 masked M1295::I110 masked M1296::I120 masked M1297::I130 masked M1298::I140 masked M1299::I150 masked M1300::I160 masked M1301::I170 masked M1302::I180 masked M1303::Swap high and low byte M1304::X input point can decide to be On-Off M1305::PLSV, DPLSV, DRVI, DDRVI, DRVA, DDRVA CH0(Y0¡BY1) the flag of opereation in reverse M1306::PLSV, DPLSV, DRVI, DDRVI, DRVA, DDRVA CH1(Y2¡BY3) the flag of operation inreverse M1310::Starting flag for immediately shut down Y10 pulse output (for SCV1.4 or over models) M1311::Starting flag for immediately shut down Y11 pulse output (for SCV1.4 or over models) M1312::C235 Start input point control M1313::C236 Start input point control M1314::C237 Start input point control M1315::C238 Start input point control M1316::C239 Start input point control M1317::C240 Start input point control M1320::C235 Reset input point control M1321::C236 Reset input point control M1322::C237 Reset input point control M1323::C238 Reset input point control M1324::C239 Reset input point control M1325::C240 Reset input point control M1328::C235 Start/Reset function enable M1329::C236 Start/Reset function enable M1330::C237 Start/Reset function enable M1331::C238 Start/Reset function enable M1332::C239 Start/Reset function enable M1333::C240 Start/Reset function enable M1334::Stop CH0 (Y0, Y1) pulse output temporarily M1335::Stop CH1 (Y2, Y3) pulse output temporarily M1336::CH0 (Y0, Y1) pulse send flag M1337::CH1 (Y2, Y3) pulse send flag M1338::Start CH0 (Y0, Y1) offset pulse flag M1339::Start CH1 (Y2, Y3) offset pulse flag M1340::To have interrupt (I110) after finishing sending CH0 (Y0, Y1) pulse M1341::To have interrupt (I120) after finishing sending CH1 (Y2, Y3) pulse M1342::To have interrupt (I130) at the same time that sending CH0 (Y0, Y1) pulse M1343::To have interrupt (I140) at the same time that sending CH1 (Y2, Y3) pulse M1344::Start CH0 (Y0, Y1) compensation pulse flag M1345::Start CH1 (Y2, Y3) compensation pulse flag M1346::ZRN CLEAR output signal enable M1347::PLSY instruction, reset CH0 (Y0, Y1) pulse after finishing output M1348::PLSY instruction, reset CH1 (Y2, Y3) pulse after finishing output M1350::PLC LINK start flag M1351::Start PLC LINK automatically M1352::Start PLC LINK by manual M1353::Start-up PLC to link more than 32 external devices and more than 16 read/write function (100 record as max.) M1354::START-UP PLC LINK THE SYNCHRONOUS READ/WRITE FUNCTION M1360::PLC LINK ID 1 exists M1361::PLC LINK ID 2 exists M1362::PLC LINK ID 3 exists M1363::PLC LINK ID 4 exists M1364::PLC LINK ID 5 exists M1365::PLC LINK ID 6 exists M1366::PLC LINK ID 7 exists M1367::PLC LINK ID 8 exists M1368::PLC LINK ID 9 exists M1369::PLC LINK ID 10 exists M1370::PLC LINK ID 11 exists M1371::PLC LINK ID 12 exists M1372::PLC LINK ID 13 exists M1373::PLC LINK ID 14 exists M1374::PLC LINK ID 15 exists M1375::PLC LINK ID 16 exists M1376::PLC LINK ID 1 acts M1377::PLC LINK ID 2 acts M1378::PLC LINK ID 3 acts M1379::PLC LINK ID 4 acts M1380::PLC LINK ID 5 acts M1381::PLC LINK ID 6 acts M1382::PLC LINK ID 7 acts M1383::PLC LINK ID 8 acts M1384::PLC LINK ID 9 acts M1385::PLC LINK ID 10 acts M1386::PLC LINK ID 11 acts M1387::PLC LINK ID 12 acts M1388::PLC LINK ID 13 acts M1389::PLC LINK ID 14 acts M1390::PLC LINK ID 15 acts M1391::PLC LINK ID 16 acts M1392::PLC LINK ID 1 ERROR M1393::PLC LINK ID 2 ERROR M1394::PLC LINK ID 3 ERROR M1395::PLC LINK ID 4 ERROR M1396::PLC LINK ID 5 ERROR M1397::PLC LINK ID 6 ERROR M1398::PLC LINK ID 7 ERROR M1399::PLC LINK ID 8 ERROR M1400::PLC LINK ID 9 ERROR M1401::PLC LINK ID 10 ERROR M1402::PLC LINK ID 11 ERROR M1403::PLC LINK ID 12 ERROR M1404::PLC LINK ID 13 ERROR M1405::PLC LINK ID 14 ERROR M1406::PLC LINK ID 15 ERROR M1407::PLC LINK ID 16 ERROR M1408::PLC LINK ID 1 read completed M1409::PLC LINK ID 2 read completed M1410::PLC LINK ID 3 read completed M1411::PLC LINK ID 4 read completed M1412::PLC LINK ID 5 read completed M1413::PLC LINK ID 6 read completed M1414::PLC LINK ID 7 read completed M1415::PLC LINK ID 8 read completed M1416::PLC LINK ID 9 read completed M1417::PLC LINK ID 10 read completed M1418::PLC LINK ID 11 read completed M1419::PLC LINK ID 12 read completed M1420::PLC LINK ID 13 read completed M1421::PLC LINK ID 14 read completed M1422::PLC LINK ID 15 read completed M1423::PLC LINK ID 16 read completed M1424::PLC LINK ID 1 write completed M1425::PLC LINK ID 2 write completed M1426::PLC LINK ID 3 write completed M1427::PLC LINK ID 4 write completed M1428::PLC LINK ID 5 write completed M1429::PLC LINK ID 6 write completed M1430::PLC LINK ID 7 write completed M1431::PLC LINK ID 8 write completed M1432::PLC LINK ID 9 write completed M1433::PLC LINK ID 10 write completed M1434::PLC LINK ID 11 write completed M1435::PLC LINK ID 12 write completed M1436::PLC LINK ID 13 write completed M1437::PLC LINK ID 14 write completed M1438::PLC LINK ID 15 write completed M1439::PLC LINK ID 16 write completed M1440::PLC LINK SLAVE ID 17 exists M1441::PLC LINK SLAVE ID 18 exists M1442::PLC LINK SLAVE ID 19 exists M1443::PLC LINK SLAVE ID 20 exists M1444::PLC LINK SLAVE ID 21 exists M1445::PLC LINK SLAVE ID 22 exists M1446::PLC LINK SLAVE ID 23 exists M1447::PLC LINK SLAVE ID 24 exists M1448::PLC LINK SLAVE ID 25 exists M1449::PLC LINK SLAVE ID 26 exists M1450::PLC LINK SLAVE ID 27 exists M1451::PLC LINK SLAVE ID 28 exists M1452::PLC LINK SLAVE ID 29 exists M1453::PLC LINK SLAVE ID 30 exists M1454::PLC LINK SLAVE ID 31 exists M1455::PLC LINK SLAVE ID 32 exists M1456::PLC LINK SLAVE ID 17 acts M1457::PLC LINK SLAVE ID 18 acts M1458::PLC LINK SLAVE ID 19 acts M1459::PLC LINK SLAVE ID 20 acts M1460::PLC LINK SLAVE ID 21 acts M1461::PLC LINK SLAVE ID 22 acts M1462::PLC LINK SLAVE ID 23 acts M1463::PLC LINK SLAVE ID 24 acts M1464::PLC LINK SLAVE ID 25 acts M1465::PLC LINK SLAVE ID 26 acts M1466::PLC LINK SLAVE ID 27 acts M1467::PLC LINK SLAVE ID 28 acts M1468::PLC LINK SLAVE ID 29 acts M1469::PLC LINK SLAVE ID 30 acts M1470::PLC LINK SLAVE ID 31 acts M1471::PLC LINK SLAVE ID 32 acts M1472::PLC LINK SLAVE ID 17 ERROR M1473::PLC LINK SLAVE ID 18 ERROR M1474::PLC LINK SLAVE ID 19 ERROR M1475::PLC LINK SLAVE ID 20 ERROR M1476::PLC LINK SLAVE ID 21 ERROR M1477::PLC LINK SLAVE ID 22 ERROR M1478::PLC LINK SLAVE ID 23 ERROR M1479::PLC LINK SLAVE ID 24 ERROR M1480::PLC LINK SLAVE ID 25 ERROR M1481::PLC LINK SLAVE ID 26 ERROR M1482::PLC LINK SLAVE ID 27 ERROR M1483::PLC LINK SLAVE ID 28 ERROR M1484::PLC LINK SLAVE ID 29 ERROR M1485::PLC LINK SLAVE ID 30 ERROR M1486::PLC LINK SLAVE ID 31 ERROR M1487::PLC LINK SLAVE ID 32 ERROR M1488::PLC LINK SLAVE ID 17 read completed M1489::PLC LINK SLAVE ID 18 read completed M1490::PLC LINK SLAVE ID 19 read completed M1491::PLC LINK SLAVE ID 20 read completed M1492::PLC LINK SLAVE ID 21 read completed M1493::PLC LINK SLAVE ID 22 read completed M1494::PLC LINK SLAVE ID 23 read completed M1495::PLC LINK SLAVE ID 24 read completed M1496::PLC LINK SLAVE ID 25 read completed M1497::PLC LINK SLAVE ID 26 read completed M1498::PLC LINK SLAVE ID 27 read completed M1499::PLC LINK SLAVE ID 28 read completed M1500::PLC LINK SLAVE ID 29 read completed M1501::PLC LINK SLAVE ID 30 read completed M1502::PLC LINK SLAVE ID 31 read completed M1503::PLC LINK SLAVE ID 32 read completed M1504::PLC LINK SLAVE ID 17 write completed M1505::PLC LINK SLAVE ID 18 write completed M1506::PLC LINK SLAVE ID 19 write completed M1507::PLC LINK SLAVE ID 20 write completed M1508::PLC LINK SLAVE ID 21 write completed M1509::PLC LINK SLAVE ID 22 write completed M1510::PLC LINK SLAVE ID 23 write completed M1511::PLC LINK SLAVE ID 24 write completed M1512::PLC LINK SLAVE ID 25 write completed M1513::PLC LINK SLAVE ID 26 write completed M1514::PLC LINK SLAVE ID 27 write completed M1515::PLC LINK SLAVE ID 28 write completed M1516::PLC LINK SLAVE ID 29 write completed M1517::PLC LINK SLAVE ID 30 write completed M1518::PLC LINK SLAVE ID 31 write completed M1519::PLC LINK SLAVE ID 32 write completed D1000::Watchdog timer (WDT) value (Unit: 1ms) D1001::DVP model number+memory capacity / type (user can read PLC program version from this register. For example, D1001 = H XX27 means version 2.7. When reading from HPP it will display Knnnnn and you can convert it to hexadecimal number by pressing <H> key. D1002::Program capacity D1003::Sum of program memory (sum of the PLC internal program memory. User can identify the content of PLC control program by this register) D1004::Check code for grammar D1005::System used D1008::STEP address when WDT timer is ON D1009::The occuring history of LV signals will be stored in D1009 D1010::Present scan time (Unit: 0.1ms) D1011::Minimum scan time (Unit: 0.1ms) D1012::Maximum scan time (Unit: 0.1ms) D1015::0~32,767(unit: 0.1ms) addition type of high-speed connection timer D1018::Geocities PI (Low byte) D1019::Geocities PI(High byte) D1020::ES/EX/SS and SC/SA/SX: X0~X7 input filter (unit: ms)EH: X0~X17 input filter (unit: ms) D1021::ES/EX/SS and SC/SA/SX: X10~X17 input delay setting (unit: ms)EH: X20~X377 input filter (unit: ms) D1022::Double frequency selection for AB phase counter of ES/EX/SS and SC/SA/SX models D1024::System used flag D1025::Communication error code D1028::Index register E0 D1029::Index register F0 D1030::Output numbers of Y0 pulse (Low word) D1031::Output numbers of Y0 pulse (High word) D1032::Output numbers of Y1 pulse (Low word) D1033::Output numbers of Y1 pulse (High word) D1034::Frequency measurement card working mode D1035::Set the number of X input point of RUN/STOP D1036::COM1(RS-232) communication protocol D1037::HKY key repeat time (ms) D1038::When PLC MPU is slave, the setting of data response delay time. The setting range is 0~10,000, and the time unit is 0.1ms. D1039::Constant scan time (ms) D1040::On state number 1 of STEP point S D1041::On state number 2 of STEP point S D1042::On state number 3 of STEP point S D1043::On state number 4 of STEP point S D1044::On state number 5 of STEP point S D1045::On state number 6 of STEP point S D1046::On state number 7 of STEP point S D1047::On state number 8 of STEP point S D1049::On number of alarm point D1050::Modbus communication data conversion. PLC will automatically convert the ASCII data saved in D1070~D1085 to HEX. D1051::Modbus communication data conversion. PLC will automatically convert the ASCII data saved in D1070~D1085 to HEX. D1052::Modbus communication data conversion. PLC will automatically convert the ASCII data saved in D1070~D1085 to HEX. D1053::Modbus communication data conversion. PLC will automatically convert the ASCII data saved in D1070~D1085 to HEX. D1054::Modbus communication data conversion. PLC will automatically convert the ASCII data saved in D1070~D1085 to HEX. D1055::Modbus communication data conversion. PLC will automatically convert the ASCII data saved in D1070~D1085 to HEX. D1056::Present value of SX/EX MPU analog input channel 0 (CH0) and EH MPU AD card channel 0 (CH0) D1057::Present value of SX/EX MPU analog input channel 1 (CH1) and EH MPU AD card channel 1 (CH1) D1058::Present value of EX MPU analog input channel 2 (CH2) D1059::Present value of EX MPU analog input channel 3 (CH3) D1061::System error message D1062::It is used to set average time (2~4 times) for SX model AD0 and AD1. D1065::System used flag D1066::System used flag D1067::Algorithm error code D1068::Lock the algorithm error address D1069::Step number of errors associated with flags M1065~M1067 D1070::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1071::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1072::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1073::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1074::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1075::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1076::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1077::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1078::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1079::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1080::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1081::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1082::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1083::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1084::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1085::When the PLC built-in RS-485 communication command receives feedback signals from receiver. The signals will be saved in the registers D1070~D1085. User can use the contents saved in the registers to check the feedback data. D1086::Low word of password setting for DVP-PCC01 (decided by the HEX value that is corresponded to ASCII character) D1087::Low word of password setting for DVP-PCC01 (decided by the HEX value that is corresponded to ASCII character) D1089::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1090::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1091::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1092::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1093::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1094::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1095::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1096::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1097::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1098::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1099::When the PLC built-in RS-485 communication command is executed, the transmitting signals will be stored in the registers D1089~D1099. User can use the contents saved in registers to check the feedback data. D1100::Once LV signal happen, Y0~Y17 will perform output based on corresponding value of D1100. D1101::Start address of file register D1102::Copy numbers of file register D1103::Set start D number for file register to store (the number should be large than 2000) D1104::Parameter index for Accel/Decel pulse output Y0 (corresponds to device D) D1109::COM3 communication protocol setting D1110::Average of SX/EX series analog input channel 0 (CH 0) and EH series DA card channel 0 (CH0) D1111::Average of SX/EX series analog input channel 1 (CH 1) and EH series DA card channel 1 (CH1) D1112::Average of EX series analog input channel 2 (CH 2) D1113::Average of EX series analog input channel 3 (CH 3) D1116::SX/EX series analog output channel 0 (CH 0) and EH series DA card channel 0 (CH0) D1117::SX/EX series analog output channel 1 (CH 1) and EH series DA card channel 0 (CH0) D1118::For SX/EX/EH model only. It is the filter wave time setting between the A/D conversions, and with the default setting as 0 and the unit as 1ms, all will be regarded as 5ms if D1118<=5. D1119::System used D1120::COM2(RS-485) Communication protocol D1121::PLC communication address (the address that save PLC communication address, it is latched) D1122::Residual words of transmitting data D1123::Residual words of receiving data D1124::Start character definition (STX) D1125::First ending character definition (EXT1) D1126::Second ending character definition (EXT2) D1127::It is the interrupt request of communication receiving of RS special words. (I150) D1129::RS-485 time-out setting (ms) D1130::MODBUS return error code record D1133::Special high-speed pulse output register (D) index D1137::Address of operator error occurs D1139::Connection number of BCD module expansion unit (the maximum is two units) D1140::Special expansion module number, maximum is 8 units D1141::System used D1142::Input points (X) of expansion unit D1143::Output points (Y) of expansion unit D1144::Parameter index for Accel/Decel pulse output of adjustable slope (corresponds to component D) D1145::Connection number of KEY module expansion unit D1146::Connection number of DISP module expansion unit D1147::Memory card type (Memory state) b0=0:NO CARD (H0000) b0=1:FLASH CARD exists b8=0:The switch of FLASH CARD is Off (H0001) b8=1:The switch of FLASH CARD is On (H0101) D1148::System used D1149::Function card type: 0:NO CARD 1:RS-232(DVP-F232),DU01(DVPDU01) 2:RS-422(DVP-F422) 3:COM3(DVP-F232S,DVP-F485S) 4:Potentiometer switch(DVP-F6VR) 5:DIP switch(DVP-F8ID) 6:Transitor output card(DVP-F2OT) 7:Digital input(DVP-F4IP) 8:2AD card (DVP-F2AD) 9:2DA card(DVP-F2DA) D1150::Table count register in multi-group setting comparison mode D1151::Table count register in frequency control mode D1152::The change value of high word of DHSZ D D1153::The change value of low word of DHSZ D D1154::Recommended Interval of accelerated time (10~32767 ms) of Accel/Decel pulse output of adjustable slope D1155::Recommended Interval of decelerated time (-1~ -32700 ms) of Accel/Decel pulse output of adjustable slope D1156::Special D that indicated by RTMU command (K0~K9) D1157::Special D that indicated by RTMU command (K0~K9) D1158::Special D that indicated by RTMU command (K0~K9) D1159::Special D that indicated by RTMU command (K0~K9) D1160::Special D that indicated by RTMU command (K0~K9) D1161::Special D that indicated by RTMU command (K0~K9) D1162::Special D that indicated by RTMU command (K0~K9) D1163::Special D that indicated by RTMU command (K0~K9) D1164::Special D that indicated by RTMU command (K0~K9) D1165::Special D that indicated by RTMU command (K0~K9) D1166::Rising-edge or falling-edge switch of X10 (SCV1.4 or over models) D1167::Rising-edge or falling-edge switch of X11 (SCV1.4 or over models) D1168::RS instruction, interrupt request when receiving specified data character (I150) D1169::RS instruction, interrupt request when receiving specified data legnth (I160) D1170::PC value when executing single step D1172::2-phase pulse output frequency (12Hz~20KHz) D1173::2-phase pulse output mode selection (K1and K2) D1174::Target number for 2-phase pulse outputs (low 16-bit) D1175::Target number for 2-phase pulse outputs (high 16-bit) D1176::Present output number of 2-phase pulse (low 16-bit) D1177::Present output number of 2-phase pulse (high 16-bit) D1178::VR0 value D1179::VR1 value D1180::16-byte (low) of high-speed counting value will be stored in D1180 when I401 happens D1181::16-byte (high) of high-speed counting value will be stored in D1181 when I401 happens D1182::Pointer register E1 D1183::Pointer register F1 D1184::Pointer register E2 D1185::Pointer register F2 D1186::Pointer register E3 D1187::Pointer register F3 D1188::Pointer register E4 D1189::Pointer register F4 D1190::Pointer register E5 D1191::Pointer register F5 D1192::Pointer register E6 D1193::Pointer register F6 D1194::Pointer register E7 D1195::Pointer register F7 D1196::Number system stting (provided for DVP-SX series only) D1197::System used D1198::16-byte (low) of high-speed counting value will be stored in D1198 when I501 happens D1199::16-byte (high) of high-speed counting value will be stored in D1199 when I501 happens D1200::Start address of M0~M999 auxiliary relay latched D1201::End address of M0~M999 auxiliary relay latched D1202::Start address of M2000~M4095 auxiliary relay latched D1203::End address of M2000~M4095 auxiliary relay latched D1204::Start latched address of 100ms timer T0~T199 D1205::End latched address of 100ms timer T0~T199 D1206::Start latched address of 10ms timer T200~T239 D1207::End latched address of 10ms timer T200~T239 D1208::Start latched address of 16-bit counter C0~C199 D1209::End latched address of 16-bit counter C0~C199 D1210::Start latched address of 32-bit counter C200~C234 D1211::End latched address of 32-bit counter C200~C234 D1212::Start latched address of 32-bit high-speed counter C235~C255 D1213::End latched address of 32-bit high-speed counter C235~C255 D1214::Start latched address of step point (S0~S1023) D1215::End latched address of step point (S0~S1023) D1216::Start latched address of register D0~D999 D1217::End latched address of register D0~D999 D1218::Start latched address of register D2000~D9999 D1219::End latched address of register D2000~D9999 D1220::The first group of pulse output phase 00: 1-phase (Y0 output) 01:A Phase 02:B Phase D1221::The second group of pulse output phase 00:1- phase (Y2 output) 01:A Phase 02:B Phase D1222::Set the time difference of CH0 between direction signal and pulse output for DRVI, DDRVI, DRVA, DDRVA, PLSV, and DPLSV. D1223::Set the time difference of CH1 between direction signal and pulse output for DRVI, DDRVI, DRVA, DDRVA, PLSV, and DPLSV. D1225::The first group of the count setting of counter (HHSC0). It is the count mode of C241, C246, C251. D1226::The second group of the count setting of counter (HHSC1). It is the count mode of C242, C247, C252. D1227::The third group of the count setting of counter (HHSC2). It is the count mode of C243, C248, C253. D1228::The forth group of the count setting of counter (HHSC3). It is the count mode of C244, C249, C254. D1256::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1257::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1258::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1259::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1260::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1261::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1262::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1263::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1264::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1265::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1266::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1267::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1268::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1269::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1270::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1271::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1272::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1273::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1274::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1275::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1276::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1277::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1278::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1279::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1280::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1281::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1282::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1283::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1284::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1285::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1286::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1287::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1288::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1289::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1290::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1291::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1292::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1293::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1294::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1295::MODRW command of RS-485 is built-in. The characters that sent during executing is saved in D1256~D1295. User can check according to the content of these registers. D1296::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1297::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1298::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1299::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1300::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1301::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1302::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1303::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1304::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1305::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1306::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1307::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1308::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1309::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1310::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1311::MODRW command of RS-485 is built-in. PLC system will convert ASCII in the content of the register that user indicates to HEX and save it in D1296 ?D1311. D1313::Real time clock (RTC) second 00~59 D1314::Real time clock (RTC) minute 00~59 D1315::Real time clock (RTC) hour 00~23 D1316::Real time clock (RTC) day 01~31 D1317::Real time clock (RTC) month 01~12 D1318::Real time clock (RTC) week 1~7 D1319::Real time clock (RTC) year 00-99 D1320::The 1st special expansion module ID D1321::The 2nd special expansion module ID D1322::The 3rd special expansion module ID D1323::The 4th special expansion module ID D1324::The 5th special expansion module ID D1325::The 6th special expansion module ID D1326::The 7th special expansion module ID D1327::The 8th special expansion module ID D1328::CH0 (Y0,Y1) offset pulse number (Low word) D1329::CH0 (Y0,Y1) offset pulse number (High word) D1330::CH1 (Y2,Y3) offset pulse number (Low word) D1331::CH1 (Y2,Y3) offset pulse number (High word) D1332::CH0 (Y0,Y1) residual pulse number (Low word) D1333::CH0 (Y0,Y1) residual pulse number (High word) D1334::CH1 (Y2,Y3) residual pulse number (Low word) D1335::CH1 (Y2,Y3) residual pulse number (High word) D1336::Present value of CH0 pulse (Low word) Y0, Y1 D1337::Present value of CH0 pulse (High word) Y0, Y1 D1338::Present value of CH1 pulse (Low word) Y2, Y3 D1339::Present value of CH1 pulse (High word) Y2, Y3 D1340::The 1st step start frequency and the last step end frequency of CH0 pulse D1341::Maximum output frequency (Low word) (it is fixed to 200KHz) D1342::Maximum output frequency (High word) (it is fixed to 200KHz) D1343::Acceleration /Deceleration time of CH0 pulse D1344::CH0 (Y0,Y1) complement pulse number (Low word) D1345::CH0 (Y0,Y1) complement pulse number (High word) D1346::CH1 (Y2,Y3) complement pulse number (Low word) D1347::CH1 (Y2,Y3) complement pulse number (High word) D1348::CH0 (Y10) current pulse value (Low word) D1349::CH0 (Y10) current pulse value (High word) D1350::CH1 (Y11) current pulse value (Low word) D1351::CH1 (Y11) current pulse value (High word) D1352::SC: the 1st step starting frequency and last step ending frequency of Y11.EH: the 2nd step starting frequency and last step ending frequency of CH1 (Y2, Y3) output D1353::SC: Y11 acceleration/deceleration time setting.EH: acceleration/deceleration time setting of 2nd group CH1 (Y2, Y3) output. D1355::Communication address that read by PLC LINK ID 1 D1356::Communication address that read by PLC LINK ID 2 D1357::Communication address that read by PLC LINK ID 3 D1358::Communication address that read by PLC LINK ID 4 D1359::Communication address that read by PLC LINK ID 5 D1360::Communication address that read by PLC LINK ID 6 D1361::Communication address that read by PLC LINK ID 7 D1362::Communication address that read by PLC LINK ID 8 D1363::Communication address that read by PLC LINK ID 9 D1364::Communication address that read by PLC LINK ID 10 D1365::Communication address that read by PLC LINK ID 11 D1366::Communication address that read by PLC LINK ID 12 D1367::Communication address that read by PLC LINK ID 13 D1368::Communication address that read by PLC LINK ID 14 D1369::Communication address that read by PLC LINK ID 15 D1370::Communication address that read by PLC LINK ID 16 D1371::When M1070 is ON, D1371 will decide the time unit of CH0 PWM pulse output D1372::When M1071 is ON, D1372 will decide the time unit of CH1 PWM pulse output D1375::The first KEY module X coordinate D1376::The first KEY module Y coordinate D1377::The first KEY module button number D1378::The second KEY module X coordinate D1379::The second KEY module Y coordinate D1380::The second KEY module button number D1381::The first BCD module (Low byte) D1382::The first BCD module (High byte) D1383::The second BCD module (Low byte) D1384::The second BCD module (High byte) D1385::The first DISP module (Low byte) D1386::The first DISP module (High byte) D1387::The decimal setting of first DISP module D1388::The second DISP module (High byte) D1389::The second DISP module (Low byte) D1390::The decimal setting of second DISP module D1391::The third DISP module (High byte) D1392::The third DISP module (Low byte) D1393::The decimal setting of third DISP module D1399::PLC LINK indicate the ID number of started SLAVE station D1415::Communication address that wrote by PLC LINK ID 1 D1416::Communication address that wrote by PLC LINK ID 2 D1417::Communication address that wrote by PLC LINK ID 3 D1418::Communication address that wrote by PLC LINK ID 4 D1419::Communication address that wrote by PLC LINK ID 5 D1420::Communication address that wrote by PLC LINK ID 6 D1421::Communication address that wrote by PLC LINK ID 7 D1422::Communication address that wrote by PLC LINK ID 8 D1423::Communication address that wrote by PLC LINK ID 9 D1424::Communication address that wrote by PLC LINK ID 10 D1425::Communication address that wrote by PLC LINK ID 11 D1426::Communication address that wrote by PLC LINK ID 12 D1427::Communication address that wrote by PLC LINK ID 13 D1428::Communication address that wrote by PLC LINK ID 14 D1429::Communication address that wrote by PLC LINK ID 15 D1430::Communication address that wrote by PLC LINK ID 16 D1431::PLC LINK times D1432::PLC LINK counts D1433::PLC LINK units D1434::Read items of PLC LINK ID 1 D1435::Read items of PLC LINK ID 2 D1436::Read items of PLC LINK ID 3 D1437::Read items of PLC LINK ID 4 D1438::Read items of PLC LINK ID 5 D1439::Read items of PLC LINK ID 6 D1440::Read items of PLC LINK ID 7 D1441::Read items of PLC LINK ID 8 D1442::Read items of PLC LINK ID 9 D1443::Read items of PLC LINK ID 10 D1444::Read items of PLC LINK ID 11 D1445::Read items of PLC LINK ID 12 D1446::Read items of PLC LINK ID 13 D1447::Read items of PLC LINK ID 14 D1448::Read items of PLC LINK ID 15 D1449::Read items of PLC LINK ID 16 D1450::Wrote items of PLC LINK ID 1 D1451::Wrote items of PLC LINK ID 2 D1452::Wrote items of PLC LINK ID 3 D1453::Wrote items of PLC LINK ID 4 D1454::Wrote items of PLC LINK ID 5 D1455::Wrote items of PLC LINK ID 6 D1456::Wrote items of PLC LINK ID 7 D1457::Wrote items of PLC LINK ID 8 D1458::Wrote items of PLC LINK ID 9 D1459::Wrote items of PLC LINK ID 10 D1460::Wrote items of PLC LINK ID 11 D1461::Wrote items of PLC LINK ID 12 D1462::Wrote items of PLC LINK ID 13 D1463::Wrote items of PLC LINK ID 14 D1464::Wrote items of PLC LINK ID 15 D1465::Wrote items of PLC LINK ID 16 D1466::CH0 the necessary pulse number for one turn of motor (low word) D1467::CH0 the necessary pulse number for one turn of motor (high word) D1468::CH1 the necessary pulse number for one turn of motor (low word) D1469::CH1 the necessary pulse number for one turn of motor (high word) D1470::CH0 the moved distance for one turn of motor (low word) D1471::CH0 the moved distance for one turn of motor (high word) D1472::CH1 the moved distance for one turn of motor (low word) D1473::CH1 the moved distance for one turn of motor (high word) D1474::CH0 mechanical unit of movement (low word) D1475::CH0 mechanical unit of movement (high word) D1476::CH1 mechanical unit of movement (low word) D1477::CH1 mechanical unit of movement (high word) D1480::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1481::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1482::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1483::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1484::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1485::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1486::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1487::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1488::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1489::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1490::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1491::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1492::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1493::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1494::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1495::ID 1 LINK PLC reads. Communication address for ID 1 reads is in D1355. The range is D100-D115 of ID 1 PLC. D1496::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1497::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1498::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1499::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1500::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1501::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1502::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1503::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1504::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1505::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1506::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1507::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1508::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1509::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1510::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1511::ID 1 LINK PLC writes. Communication address for ID 1 writes is in D1415. The range is D200-D215 of ID 1 PLC. D1512::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527.. D1513::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1514::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1515::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1516::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1517::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1518::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1519::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1520::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1521::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1522::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1523::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1524::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1525::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1526::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1527::When M1353=Off, SLAVE ID 2 LINK PLC reads. Communication address for SLAVE ID 2 reads is in D1356. The range is D100-D115 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address read from SLAVE ID17~32 will be saved in D1512~1527. D1528::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1529::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1530::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1531::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1532::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1533::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1534::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1535::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1536::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1537::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1538::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1539::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1540::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1541::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1542::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1543::When M1353=Off, SLAVE ID 2 LINK PLC writes. Communication address for SLAVE ID 2 writes is in D1416. The range is D200-D215 of SLAVE ID 2 PLC.For EH series MPU only, when M1353=On, communication address saved in D1528~1543 will be written into SLAVE ID17~32. D1544::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1545::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1546::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1547::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1548::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1549::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1550::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1551::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1552::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1553::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1554::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1555::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1556::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1557::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1558::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1559::When M1353=Off, SLAVE ID 3 LINK PLC reads. Communication address for SLAVE ID 3 reads is in D1357. The range is D100-D115 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to read from SLAVE ID17~32 is saved in D1544~1559. D1560::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1561::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1562::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1563::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1564::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1565::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1566::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1567::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1568::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1569::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1570::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1571::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1572::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1573::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1574::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1575::When M1353=Off, SLAVE ID 3 LINK PLC writes. Communication address for SLAVE ID 3 writes is in D1417. The range is D200-D215 of SLAVE ID 3 PLC.For EH series MPU only, when M1353=On, the data length for PLC to write into SLAVE ID 17~32 is saved in D1560~1575. D1576::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1577::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1578::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1579::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1580::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1581::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1582::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1583::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1584::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1585::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1586::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1587::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1588::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1589::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1590::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1591::M1353=Off, SLAVE ID 4 LINK PLC reads. Communication address for SLAVE ID 4 reads is in D1358. The range is D100-D115 of SLAVE ID 4 PLC.For EH series MPU only, when M1353=On, the started register for PLC to save the data read from SLAVE ID17~32 is saved in D1576~1591. D1592::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1593::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1594::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1595::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1596::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1597::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1598::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1599::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1600::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1601::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1602::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1603::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1604::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1605::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1606::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1607::ID 4 LINK PLC writes. Communication address for ID 4 writes is in D1418. The range is D200-D215 of ID 4 PLC. D1608::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1609::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1610::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1611::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1612::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1613::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1614::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1615::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1616::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1617::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1618::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1619::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1620::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1621::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1622::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1623::ID 5 LINK PLC reads. Communication address for ID 5 reads is in D1359. The range is D100-D115 of ID 5 PLC. D1624::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1625::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1626::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1627::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1628::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1629::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1630::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1631::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1632::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1633::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1634::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1635::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1636::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1637::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1638::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1639::ID 5 LINK PLC writes. Communication address for ID 5 writes is in D1419. The range is D200-D215 of ID 5 PLC. D1640::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1641::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1642::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1643::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1644::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1645::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1646::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1647::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1648::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1649::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1650::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1651::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1652::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1653::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1654::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1655::ID 6 LINK PLC reads. Communication address for ID 6 reads is in D1360. The range is D100-D115 of ID 6 PLC. D1656::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1657::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1658::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1659::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1660::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1661::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1662::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1663::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1664::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1665::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1666::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1667::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1668::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1669::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1670::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1671::ID 6 LINK PLC writes. Communication address for ID 6 writes is in D1420. The range is D200-D215 of ID 6 PLC. D1672::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1673::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1674::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1675::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1676::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1677::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1678::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1679::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1680::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1681::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1682::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1683::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1684::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1685::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1686::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1687::ID 7 LINK PLC reads. Communication address for ID 7 reads is in D1361. The range is D100-D115 of ID 7 PLC. D1688::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1689::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1690::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1691::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1692::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1693::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1694::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1695::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1696::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1697::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1698::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1699::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1700::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1701::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1702::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1703::ID 7 LINK PLC writes. Communication address for ID 7 writes is in D1421. The range is D200-D215 of ID 7 PLC. D1704::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1705::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1706::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1707::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1708::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1709::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1710::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1711::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1712::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1713::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1714::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1715::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1716::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1717::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1718::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1719::ID 8 LINK PLC reads. Communication address for ID 8 reads is in D1362. The range is D100-D115 of ID 8 PLC. D1720::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1721::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1722::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1723::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1724::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1725::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1726::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1727::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1728::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1729::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1730::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1731::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1732::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1733::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1734::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1735::ID 8 LINK PLC writes. Communication address for ID 8 writes is in D1422. The range is D200-D215 of ID 8 PLC. D1736::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1737::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1738::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1739::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1740::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1741::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1742::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1743::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1744::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1745::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1746::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1747::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1748::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1749::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1750::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1751::SLAVE ID 9 LINK PLC reads. Communication address for SLAVE ID 9 reads is in D1363. The range is D100-D115 of SLAVE ID 9 PLC. D1752::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1753::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1754::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1755::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1756::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1757::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1758::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1759::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1760::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1761::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1762::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1763::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1764::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1765::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1766::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1767::ID 9 LINK PLC writes. Communication address for ID 9 writes is in D1423. The range is D200-D215 of ID 9 PLC. D1768::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1769::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1770::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1771::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1772::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1773::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1774::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1775::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1776::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1777::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1778::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1779::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1780::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1781::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1782::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1783::ID 10 LINK PLC reads. Communication address for ID 10 reads is in D1364. The range is D100-D115 of ID 10 PLC. D1784::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1785::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1786::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1787::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1788::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1789::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1790::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1791::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1792::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1793::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1794::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1795::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1796::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1797::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1798::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1799::ID 10 LINK PLC writes. Communication address for ID 10 writes is in D1424. The range is D200-D215 of ID 10 PLC. D1800::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1801::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1802::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1803::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1804::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1805::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1806::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1807::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1808::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1809::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1810::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1811::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1812::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1813::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1814::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1815::ID 11 LINK PLC reads. Communication address for ID 11 reads is in D1365. The range is D100-D115 of ID 11 PLC. D1816::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1817::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1818::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1819::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1820::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1821::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1822::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1823::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1824::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1825::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1826::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1827::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1828::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1829::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1830::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1831::ID 11 LINK PLC writes. Communication address for ID 11 writes is in D1425. The range is D200-D215 of ID 11 PLC. D1832::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1833::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1834::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1835::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1836::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1837::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1838::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1839::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1840::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1841::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1842::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1843::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1844::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1845::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1846::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1847::ID 12 LINK PLC reads. Communication address for ID 12 reads is in D1366. The range is D100-D115 of ID 12 PLC. D1848::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1849::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1850::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1851::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1852::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1853::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1854::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1855::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1856::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1857::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1858::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1859::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1860::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1861::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1862::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1863::ID 12 LINK PLC writes. Communication address for ID 12 writes is in D1426. The range is D200-D215 of ID 12 PLC. D1864::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1865::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1866::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1867::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1868::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1869::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1870::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1871::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1872::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1873::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1874::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1875::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1876::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1877::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1878::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1879::ID 13 LINK PLC reads. Communication address for ID 13 reads is in D1367. The range is D100-D115 of ID 13 PLC. D1880::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1881::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1882::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1883::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1884::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1885::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1886::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1887::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1888::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1889::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1890::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1891::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1892::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1893::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1894::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1895::ID 13 LINK PLC writes. Communication address for ID 13 writes is in D1427. The range is D200-D215 of ID 13 PLC. D1896::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1897::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1898::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1899::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1900::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1901::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1902::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1903::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1904::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1905::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1906::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1907::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1908::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1909::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1910::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1911::ID 14 LINK PLC reads. Communication address for ID 14 reads is in D1368. The range is D100-D115 of ID 14 PLC. D1912::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1913::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1914::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1915::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1916::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1917::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1918::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1919::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1920::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1921::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1922::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1923::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1924::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1925::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1926::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1927::ID 14 LINK PLC writes. Communication address for ID 14 writes is in D1428. The range is D200-D215 of ID 14 PLC. D1928::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1929::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1930::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1931::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1932::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1933::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1934::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1935::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1936::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1937::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1938::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1939::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1940::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1941::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1942::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1943::ID 15 LINK PLC reads. Communication address for ID 15 reads is in D1369. The range is D100-D115 of ID 15 PLC. D1944::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1945::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1946::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1947::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1948::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1949::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1950::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1951::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1952::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1953::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1954::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1955::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1956::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1957::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1958::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1959::ID 15 LINK PLC writes. Communication address for ID 15 writes is in D1429. The range is D200-D215 of ID 15 PLC. D1960::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1961::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1962::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1963::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1964::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1965::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1966::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1967::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1968::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1969::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1970::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1971::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1972::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1973::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1974::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1975::ID 16 LINK PLC reads. Communication address for ID 16 reads is in D1370. The range is D100-D115 of ID 16 PLC. D1976::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1977::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1978::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1979::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1980::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1981::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1982::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1983::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1984::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1985::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1986::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1987::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1988::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1989::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1990::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC. D1991::ID 16 LINK PLC writes. Communication address for ID 16 writes is in D1430. The range is D200-D215 of ID 16 PLC.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.