1. nx10100d.zip Driver
2. SCOUNIX.TXT File Contents

SCOUNIX.TXT Driver File Contents (nx10100d.zip)

<=================================================================>
<                 32-BIT PCI FAST ETHERNET ADAPTER                >
<                      SCO UNIX STREAM DRIVER                     >
<=================================================================>


The unix driver contained in the directory \SCO is for the
following PCI Ethernet adapter:

        32-bit PCI Fast Ethernet Adapter

  Contents:
  ---------

        A. Installing MDI Unix Driver for SCO ODT 5.0
        B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0)


File Description
================

5.X\            SCO ODT 5.0 MDI Unix Driver

3.X\            SCO 3.2.4 (ODT 3.0) LLI Unix Driver

SCOUNIX.TXT     this file


A.) Installing MDI Unix Driver for SCO ODT 5.0
==============================================

1. Login to the UNIX system as supervisor (root) and enter Maintenance mode.

    (Note: Make sure that the current directory is "/"
     using UNIX command - pwd.)

2. Please follow the following steps to uncompress the package file:

   >  cd /tmp   (and insert the package floppy in the proper drive, i.e. a:)
   >  doscp a:/sco/5.x/vol.000 ./VOL.000.000

   Now the package installation directory is ready for installing.

3. The following sections describe the configuration of the driver.
   It is suggested that you perform these instructions in a
   singler-user environment.

   Run the custom utility and select the "Install new package"
   option.

   Select Media Type "Media Image" and type Image Directory "/tmp"
   It will prompt with "32-bit PCI Fast Ethernet Adapter (ver 1.0.2)"

   After running the custom utility and the new package is installed,
   you should use the "netconfig" command to add the driver into your
   system like in step 4 below.

4. Run "netconfig". Add the desired chain.

5. When the chain has been configured, select 'q' from the
   netconfig menu. and relink the kernel at the prompt.

6. To activate the adapter, you must reboot. When the system
   boots, you should see the following message among the
   other configuration messages:

    %ethernet  0xD800-0xD81F   11   -   type=100 addr=00-00-e0-xx-xx-xx
                               .
                               .
                               .
     auto mode
     choice is auto negotiation mode
     Speed is 100 Mbps

   with the appropriate I/O addresses, IRQ, Adapter Type, IEEE address and
   medium mode (auto,100full,100half,10full,10half).
   The display of the last three bytes of the IEEE address depends on the 
   adapter currently plugged into your system.

7. If you encounter any problems during installation,
   (i.e., an error message appears on screen) call your dealer for assistance.



B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0)
======================================================

 1. Plug the 32-bit PCI Fast Ethernet Adapter into the PCI slot
    on your PC machine.

 2. Turn ON the machine and login as "root" user. (In maintenance mode)

 3. Insert the 32-bit SCO UNIX Driver diskette in drive A: and
    enter the following command from Unix Shell to install the
    SCO Unix driver.

        # cd /tmp
        # doscp a:/sco/3.x/install .
        # chmod +x install
        # ./install

 4. The screen will prompt with the following message,

      Install 32-bit PCI Fast Ethernet Adapter LLI Driver
      Please input source path ? (ex.: a:/sco/3.x)

 5. Enter the driver's full path (a:/sco/3.x) and press the ENTER key
    to start copying the driver files to the Unix system.

 6. Run the "netconfig" command from the Unix shell.

        # netconfig

 7. Select "1. Add a chain" from the chain configuration options.

 8. Select "4. sco_tcp   SCO TCP/IP for UNIX" from the protocol 
    configuration options.

 9. Select "18. r7e0   32-bit PCI Fast Ethernet Adapter LLI
    Driver, board 0" from the driver configuration options.

10. The system will prompt with the following messages to complete
    configuring the driver chain,
        ...
      Add chain sco_tcp->r7e0 (y/n): y
        ...
      Enter auto, force 100 or 10bps: (auto 10 100) [auto]
      or 'q' to quit: (press Enter key)
        ...
      Enter the internet address of this interface: 203.70.236.92
      Enter the netmask for this interface (default: 255.255.255.0):
      (press the Enter key)
      Does the interface use a broadcast address of all 1's? (y/n)
      (default: y): (press the Enter key)
      Enter the broadcast address for this interface (default:
      203.70.236.255): (press the Enter key)
         ...
      Are these values correct? (y/n): y
         ...
      Enter local host name or enter q to quit [sco324]: (press the Enter key)
         ...
      32 Pseudo ttys ...
         ...
      Select an option or enter q to quit [q]: (press the Enter key)
         ...
      256 TCP connections ...
         ...
      Select an option or enter q to quit [q]: (press the Enter key)
         ...

11. Select "q. Quit" from the chain configuration options.
12. The system will prompt with the following message to relink
    the system kernel file,
         ...
      Do you want to relink the kernel now? y
         ...
      Do you want this kernel to boot by default? (y/n) y
         ...
      Do you want the kernel environment rebuilt? (y/n) y
         ...

13. Reboot the unix system to initialize the driver fuction.

        # reboot



TRADEMARKS
==========

All Tademarks or Brand names mentioned are properties of
their respective companies.

== End of File ==